- 您现在的位置：买卖IC网 > PDF目录299560 > NQ80220 (LSI CORP) 100BASE-TX/10BASE-T Ethernet Media Interface Adapter PDF资料下载
参数资料
| 型号： | NQ80220 |
| 厂商： | LSI CORP |
| 元件分类： | 网络接口 |
| 英文描述： | 100BASE-TX/10BASE-T Ethernet Media Interface Adapter |
| 中文描述： | DATACOM, ETHERNET TRANSCEIVER, PQCC44 |
| 封装： | PLASTIC, LCC-44 |
| 文件页数： | 18/91页 |
| 文件大小： | 907K |
| 代理商： | NQ80220 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页
80220/80221
4-25
MD400159/E
25
3.16 FULL DUPLEX MODE
3.16.1 100 Mbps
Full Duplex mode allows transmission and reception to
occur simultaneously. When Full Duplex mode is enabled,
collision is disabled and internal TX_EN to CRS loopback
is disabled.
The device can be either forced into Half or Full Duplex
mode, or the device can detect either Half or Full Duplex
capability from a remote device and automatically place
itself in the correct mode.
The device can be forced into the Full or Half Duplex
modes by setting the duplex bit in the MI serial port Control
register.
The device can automatically configure itself for Full or
Half Duplex modes by using the AutoNegotiation algo-
rithm to advertise and detect Full and Half Duplex capabili-
ties to and from a remote terminal. All of this is described
in detail in the Link Integrity and AutoNegotiation section.
3.16.2 10 Mbps
Full Duplex in 10 Mbps mode is identical to the 100 Mbps
mode.
3.16.3 Full Duplex Indication
Full Duplex detection can be monitored through the duplex
bit in the MI serial port Status Output register, or it can also
be programmed to appear on the PLED1 pin by appropri-
ately setting the programmable LED output select bits in
the MI serial port Configuration 2 register as described in
Table 5. When the PLED1 pin is programmed to be a Full
Duplex detect output, this pin is asserted low when the
device is configured for Full Duplex operation. The PLED1
output has both pullup and pulldown driver transistors and
a weak pullup resistor, so it can drive an LED from either
VCC or GND and can also drive a digital input.
3.17 100/10 MBPS SELECTION
3.17.1 General
The device can be forced into either the 100 or 10 Mbps
mode, or the device also can detect 100 or 10 Mbps
capability from a remote device and automatically place
itself in the correct mode.
The device can be forced into either the 100 or 10 Mbps
mode by setting the speed select bit in the MI serial port
Control register.
The device can automatically configure itself for 100 or 10
Mbps mode by using the AutoNegotiation algorithm to
advertise and detect 100 and 10 Mbps capabilities to and
from a remote terminal. All of this is described in detail in
the Link Integrity & AutoNegotiation section.
3.17.2 10/100 Mbps Indication
The device speed (100/10 Mbps) can be determined
through the speed bit in the MI serial port Status Output
register, or it can also be programmed to appear on the
PLED0 pin by setting the
programmable LED output
select bits in the MI serial port Configuration 2 register.
When the PLED0 pin is programmed to be speed detect
output, this pin is asserted low when the device is config-
ured for 100 Mbps operation. The PLED0 output has both
pullup and pulldown driver transistors and a weak pullup
resistor, so it can drive an LED from either VCC or GND
and can also drive a digital input.
3.18 LOOPBACK
3.18.1 Internal CRS Loopback
TX_EN is internally looped back onto CRS during every
transmit packet. This internal CRS loopback is disabled
during collision, in Full Duplex mode, in Link Fail State, and
when the transmit disable bit is set in the MI serial port
Configuration 1 register. In 10 Mbps mode, internal CRS
loopback is also disabled when jabber is detected.
The internal CRS loopback can be disabled by setting the
TX_EN to CRS loopback disable bit in the MI serial port
Configuration 1 register. When this bit is set, TX_EN is no
longer looped back to CRS.
相关PDF资料 |
PDF描述 |
|---|---|
| NRLM332M35VF | Large Can Aluminum Electrolytic Capacitors |
| NRLM332M400V20X25F | Large Can Aluminum Electrolytic Capacitors |
| NRLM332M400V20X30F | Large Can Aluminum Electrolytic Capacitors |
| NRLM332M450VF | Large Can Aluminum Electrolytic Capacitors |
| NRLM332M50V20X25F | Large Can Aluminum Electrolytic Capacitors |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NQ80225 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:LAN Transceiver |
| NQ8023A | 制造商:未知厂家 制造商全称:未知厂家 功能描述:MCC Manchester Code Converter |
| NQ80331M250 S L822 | 制造商:Intel 功能描述:I/O Processor FCBGA3 |
| NQ80331M250 S L826 | 制造商:Intel 功能描述:I/O Processor FCBGA3 制造商:Intel 功能描述:LINDSAY, 32BIT PROCESSOR - Tape and Reel |
| NQ80331M250 S L82Q | 制造商:Intel 功能描述:I/O Processor |
发布紧急采购，3分钟左右您将得到回复。