- 您现在的位置：买卖IC网 > PDF目录16653 > NT-4-0-SP (TE Connectivity)HEAT SHRINK TUBING PDF资料下载
参数资料
| 型号： | NT-4-0-SP |
| 厂商： | TE Connectivity |
| 文件页数： | 3/6页 |
| 文件大小： | 0K |
| 描述： | HEAT SHRINK TUBING |
| 标准包装： | 50 |
| 系列： | NT |
| 类型： | 套管，弹性 |
| 收缩比率： | 1.75 至 1 |
| 内径 - 提供： | 4.000"（101.6mm） |
| 内径 - 恢复： | 2.280"（57.9mm） |
| 已恢复的墙壁厚度： | 0.139"（3.55mm） |
| 材质： | 聚烯烃 |
| 特点： | 防水 |
| 颜色： | 黑 |
| 其它名称： | 5550134002 |
SPECIFICATION RT-510 ISSUE 12
Page 3
4.3.1
Dimensions and Longitudinal Change
Three 6 inch (150 mm) specimens of tubing, as supplied, shall be measured for length ± 1/32 inch
(± 1 mm) and inside diameter in accordance with ASTM D2671, conditioned for 10 minutes in a
175 ± 5°C (347 ± 9°F ) oven, cooled to 23 ± 3°C (73 ± 5°F) and then re-measured. Prior to and after
conditioning, the dimensions of the tubing shall be in accordance with Table 1 and the longitudinal change
shall be in accordance with Table 3. Longitudinal change shall be calculated as follows:
C =
L1 - L0
L0
x 100
Where:
C
L0
L1
=
=
=
Longitudinal Change [Percent]
Length Before Conditioning [inches (mm)]
Length After Conditioning [inches (mm)]
4.3.2
4.3.3
4.4
5.0
5.1
5.2
Tensile Strength, Tensile Stress and Ultimate Elongation
Test three specimens of tubing for tensile strength and ultimate elongation in accordance with
ASTM D2671 and for tensile stress in accordance with ASTM D412.
The rate of jaw separation shall be 20 ± 2 inches (500 ± 50 mm) per minute.
Copper Stability
Three 6 inch (150 mm) specimens of tubing shall be slid over snug fitting, straight, clean, bare copper
mandrels, either solid or tubular. The specimens on the mandrels shall be conditioned for 24 hours in a
desiccator or similar humidity chamber at 90 to 95 percent relative humidity and 25 ± 3°C (77 ± 5°F) . The
specimens on the mandrels then shall be conditioned for 168 hours in a 121 ± 2°C (250 ± 4°F) oven. After
conditioning, the specimens shall be removed from the oven, cooled to 23 ± 3°C (73 ± 5°F) . The copper
mandrels shall then be removed from the tubing, then the tubing and copper mandrels shall be examined.
Darkening of the copper due to normal air oxidation shall not be cause for rejection. The tubing shall be
tested for Ultimate Elongation in accordance with 4.3.2.
Rejection And Retest
Failure of any sample of tubing to comply with any one of the requirements of this specification shall be
cause for rejection of the lot represented. Tubing which has been rejected may be replaced or reworked to
correct the defect and then resubmitted for acceptance. Before resubmitting, full particulars concerning the
rejection and the action taken to correct the defect shall be furnished to the inspector.
Preparation for Delivery
Packaging
Packaging shall be in accordance with good commercial practice. The shipping container shall be not be
less than 125 pound-test fiberboard.
Marking
Each container of tubing shall be permanently and legibly marked with the size, quantity, manufacturer's
identification and lot number.
If this document is printed it becomes uncontrolled. Check for the latest revision.
? 2005-2010 Tyco Electronics Corporation. All rights reserved
相关PDF资料 |
PDF描述 |
|---|---|
| CB5061-000 | HEAT SHRINK TUBING |
| CB5138-000 | HEAT SHRINK TUBING |
| PCX1C391MCL1GS | CAP ALUM 390UF 16V 20% SMD |
| ECA22DTKI-S288 | CONN EDGECARD 44POS .125 EXTEND |
| GCC20DRXS | CONN EDGECARD 40POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NT-4-0-SP-CS7029 | 制造商:TE Connectivity 功能描述:NT-4-0-SP-CS7029 |
| NT4-10 | 功能描述:NUT PKG 12 RoHS:是 类别:盒，外壳，支架 >> 卡架 - 配件 系列:VectorPak™ 标准包装:1 系列:VectorPak™ 附件类型:EFP 模块 适用于相关产品:PCB |
| N-T41508-106 | 制造商:ITT Interconnect Solutions 功能描述:NT41508106 / 041508-0106 / Circular |
| N-T41508-114 | 制造商:ITT Interconnect Solutions 功能描述:NT41508114 / 041508-0114 / Circular |
| NT-41A0-0482 | 功能描述:大功率LED - 单色 Red Atlas Series RoHS:否 制造商:Cree, Inc. 照明颜色:Blue 波长:465 nm 光强度: 光通量/辐射通量:500 mW 正向电流:350 mA 正向电压:3.1 V 安装风格:SMD/SMT 功率额定值: 系列:XB-D 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。