- 您现在的位置：买卖IC网 > PDF目录17000 > OCB100AZ (TT Electronics/Optek Technology)BOARD CALIBR CIRCUIT PCB MNT PDF资料下载
参数资料
| 型号： | OCB100AZ |
| 厂商： | TT Electronics/Optek Technology |
| 文件页数： | 6/24页 |
| 文件大小： | 0K |
| 描述： | BOARD CALIBR CIRCUIT PCB MNT |
| 标准包装： | 1 |
| 附件类型： | 接口板 |
| 适用于相关产品： | 光隔离器（光耦合器） |
| 产品目录页面： | 2788 (CN2011-ZH PDF) |
| 配用： | 365-1507-ND - KIT CALIBRATION CIRC OPTO ASSY |
| 其它名称： | 365-1533 |
preset phototransistor output level is reached.
At this time, the LED drive current is locked and maintained until
the calibration pin is grounded. If for some reason the LED drive cur-
rent reaches the maximum allowable value, a RED warning light will
turn on. During the calibration process, remote monitoring of J1-Pin
5 allows the designer to ensure the system is calibrated (this output
should be at the preset calibrated output level of 1/2 Vcc when the
calibration procedure is completed). Adjusting the phototransistor
load resistor may allow the system to calibrate properly.
After the calibration process is complete, the device is ready for
acknowledgement of a change in the signal. The design engineer
6
can monitor either the Analog Output (J1-Pin 5) or Logical Output
(J1-Pin 2 or J1-Pin 3).
Connection of the analog ouput to additional circuitry allows the
design engineer to set any reference point to recognize an optical
change for the device being monitored. The Analog Output can be
used with reflective devices to monitor small changes in the distance
from the device.
The Logical Output will change state once the preset optical light
condition is reached. Logic Out A” (mating connector orange wire)
switches when the optical output signal decreases below approxi-
mately 1/3 of Vcc while “Logic Out B” (mating connector blue wire)
switches when the optical output signal increases above approxi-
mately 2/3 of Vcc.
As with all optical devices with logic outputs, the switching condition
is consistent with the phototransistor receiving a preset light level.
OCB100-KIT
相关PDF资料 |
PDF描述 |
|---|---|
| 381LR471M250K022 | CAP ALUM 470UF 250V 20% SNAP |
| L-05B5N6SV6T | IND CER RF 5.6NH 0201 |
| 381LR101M400J012 | CAP ALUM 100UF 400V 20% SNAP |
| VI-20N-EY | CONVERTER MOD DC/DC 18.5V 50W |
| GBM15DCBT-S189 | CONN EDGECARD 30POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| OCB100CZ | 功能描述:光学传感器开发工具 Calibration Circuit Wired Opto Assembly RoHS:否 制造商:ams 工具用于评估: 接口类型: 最大工作温度: |
| OCB100-KIT | 功能描述:光学传感器开发工具 Sensor Design Kit Trans, Reflec, Fluid RoHS:否 制造商:ams 工具用于评估: 接口类型: 最大工作温度: |
| OCB100-KIT | 制造商:TT Electronics / OPTEK Technology 功能描述:Auto-Calibration Design Kit |
| OCB-1250 | 制造商:Heyco Products Inc 功能描述: |
| OCB-1375 | 制造商:Heyco Products Inc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。