- 您现在的位置：买卖IC网 > PDF目录1234 > OCB100CZ (TT Electronics/Optek Technology)BOARD CALIBR WIRED OPTO ASSY PDF资料下载
参数资料
| 型号： | OCB100CZ |
| 厂商： | TT Electronics/Optek Technology |
| 文件页数： | 11/24页 |
| 文件大小： | 0K |
| 描述： | BOARD CALIBR WIRED OPTO ASSY |
| 标准包装： | 25 |
| 附件类型： | 接口板 |
| 适用于相关产品： | 光隔离器（光耦合器） |
| 产品目录页面： | 2788 (CN2011-ZH PDF) |
| 配用： | 365-1507-ND - KIT CALIBRATION CIRC OPTO ASSY |
| 其它名称： | 365-1534 |
USING THE OPB732CZ WITH THE OCB100CZ
Connect the OCB100CZ to a power source as described on page 7
“Powering up the OCB100CZ”.
Plug the OPB732CZ connector into the 4 pin Molex mating connec-
tor on the OCB100CZ , and then apply power to the circuit. Adjust the
phototransistor emitter load resistor to equal approximately 10Kohms
(RL @ 10K) by placing the shorting bar on the board betweens pins 2 &
3 (see table on pg. 9) of the header. Point the OPB732CZ at a sheet of
white paper and position its front surface about ? ” from the paper.
While holding the sensor in this position, momentarily ground the pin
4 of connector J1 by touching the green wire of the mating connector
to the black wire (ground) of the mating connector.
After approximately 2-3 seconds you should see an onboard green
LED flash three times to indicate that the sensor has been calibrated
at the distance it is held from the paper. If the unit calibrated correctly,
and you have not allowed the sensor to move from the position it was
calibrated at, there will be no LEDs lit on the calibration PCB. This
means that the LED drive has ramped up to a current level sufficient to
generate an output voltage level (V OUT ) @ to ? Vcc.
Now slowly move the sensor away from the sheet of paper until a
green LED lights on the PCB. This light indicates that V OUT has dropped
to 1/3 Vcc or less. As you move the sensor closer to the paper, this
green LED will go out and then come back on at a distance very close to
the surface of the paper. At some distance between the two distances
OPTEK gives you the tools to help you take your ideas to market.
11
相关PDF资料 |
PDF描述 |
|---|---|
| OM10049 | EMULATOR PROGRAMMER LPC9X MCU |
| OPAMPEVM-PDIP | UNIV EVAL MOD FOR DIP PKG |
| OPB780KIT | KIT COLOR SENSOR OPB780Z |
| OPENLPPOL-EVB | BOARD EVAL OPEN-LOOP POL |
| OVPL5W3K | KIT DESIGN POWER LINE WHITE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| OCB100-KIT | 功能描述:光学传感器开发工具 Sensor Design Kit Trans, Reflec, Fluid RoHS:否 制造商:ams 工具用于评估: 接口类型: 最大工作温度: |
| OCB100-KIT | 制造商:TT Electronics / OPTEK Technology 功能描述:Auto-Calibration Design Kit |
| OCB-1250 | 制造商:Heyco Products Inc 功能描述: |
| OCB-1375 | 制造商:Heyco Products Inc 功能描述: |
| OCB-1500 | 制造商:Heyco Products Inc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。