参数资料
型号: OKY2-T/10-W5N-C
厂商: Murata Power Solutions Inc
文件页数: 5/16页
文件大小: 0K
描述: CONV DC/DC 33W 5V IN 10A OUT SMD
产品培训模块: Okami Series
产品目录绘图: OKY Series Converter
特色产品: Okami? Series PoL Converters
标准包装: 1
系列: Okami™ OKY-T/10-W5
类型: 非隔离(POL)
输出数: 1
电压 - 输入(最小): 2.4V
电压 - 输入(最大): 5.5V
Voltage - Output 1: 0.75 ~ 3.63 V
电流 - 输出(最大): 10A
电源(瓦) - 制造商系列: 33W
安装类型: 表面贴装
封装/外壳: 7-DIP SMD 模块
尺寸/尺寸: 1.30" L x 0.53" W x 0.33" H(33.0mm x 13.5mm x 8.3mm)
包装: 标准包装
效率: 95%
电源(瓦特)- 最大: 33W
产品目录页面: 2720 (CN2011-ZH PDF)
其它名称: 811-2146-6
OKY -T/10 & T/16-W5 Series
Programmable DOSA-SMT 10/16-Amp DC/DC Converters
Speci?cation Notes, Cont.:
Soldering Guidelines
(5)
(6)
(7)
(8)
(9)
The On/Off Control Input should use either a switch or an open collector/open drain transistor referenced
to -Input Common. A logic gate may also be used by applying appropriate external voltages which do not
exceed +Vin.
Short circuit shutdown begins when the output voltage degrades approximately 2% from the selected
setting.
For W5 models, the Input Voltage must exceed the Output Voltage at all times by 0.5 Volts or greater.
Output noise may be further reduced by adding an external filter. At zero output current, the output may
contain low frequency components which exceed the ripple specification. The output may be operated
indefinitely with no load.
All models are fully operational and meet published specifications, including “cold start” at –40° C.
Murata Power Solutions recommends the speci?cations below when installing these
converters. These speci?cations vary depending on the solder type. Exceeding these
speci?cations may cause damage to the product. Your production environment
may differ therefore please thoroughly review these guidelines with your process
engineers.
Reflow Solder Operations for surface-mount products (SMT)
(10) Regulation specifications describe the deviation as the line input voltage or output load current is varied
from a nominal midpoint value to either extreme.
For Sn/Ag/Cu based solders:
(11) Other input or output voltage ranges will be reviewed under scheduled quantity special order.
(12) Maximum PC board temperature is measured with the sensor in the center of the converter.
(13) Do not exceed maximum power specifications when adjusting the output trim.
(14) The maximum output capacitive loads depend on the the Equivalent Series Resistance (ESR) of the external
output capacitor and, to a lesser extent, the distance and series impedance to the load. Larger caps will
reduce output noise but may change the transient response. Newer ceramic caps with very low ESR may
require lower capacitor values to avoid instability. Thoroughly test your capacitors in the application. Please
refer to the Output Capacitive Load Application Note.
(15) Do not allow the input voltage to degrade lower than the input undervoltage shutdown voltage at all times.
Otherwise, you risk having the converter turn off. The undervoltage shutdown is not latching and will
attempt to recover when the input is brought back into normal operating range.
(16) The outputs are not intended to sink appreciable reverse current.
(17) “Hiccup” overcurrent operation repeatedly attempts to restart the converter with a brief, full-current output.
If the overcurrent condition still exists, the restart current will be removed and then tried again. This short
Preheat Temperature
Time over Liquidus
Maximum Peak Temperature
Cooling Rate
For Sn/Pb based solders:
Preheat Temperature
Time over Liquidus
Maximum Peak Temperature
Cooling Rate
Less than 1 oC. per second
45 to 75 seconds
260 oC.
Less than 3 oC. per second
Less than 1 oC. per second
60 to 75 seconds
235 oC.
Less than 3 oC. per second
current pulse prevents overheating and damaging the converter. Once the fault is removed, the converter
immediately recovers normal operation.
Recommended Lead-free Solder Re?ow Pro?le
Output Voltage Adustment
The output voltage may be adjusted over a limited range by connecting an
external trim resistor (Rtrim) between the Trim pin and Ground. The Rtrim
resistor must be a 1/10 Watt precision metal ?lm type, ±1% accuracy or
250
200
Peak Temp.
235-260° C
better with low temperature coef?cient, ±100 ppm/oC. or better. Mount the
resistor close to the converter with very short leads or use a surface mount
150
Soaking Zone
Re?ow Zone
time above 217° C
trim resistor.
100
120 sec max
45-75 sec
In the tables below, the calculated resistance is given. Do not exceed the
speci?ed limits of the output voltage or the converter’s maximum power
50
<1.5° C/sec
Preheating Zone
High trace = normal upper limit
Low trace = normal lower limit
rating when applying these resistors. Also, avoid high noise at the Trim
input. However, to prevent instability, you should never connect any capaci-
0
240 sec max
tors to Trim.
0
30
60
90
120
150
Time (sec)
180
210
240
270
300
High trace = normal upper limit
OKY-T/10-W5, -T/16-W5
Output Voltage
3.3 V.
2.5 V.
2.0 V.
1.8 V.
1.5 V.
1.2 V.
1.0 V.
0.7525 V.
Calculated Rtrim (KΩ)
3.160
6.947
11.780
15.004
23.077
41.973
80.021
∞ (open)
Low trace - normal lower limit
R TRIM ( ? ) = _____________ – 5110
Resistor Trim Equation, W5 models:
21070
V OUT – 0.7525V
www.murata-ps.com/support
MDC_OKY_T10T16.W5.A05 Page 5 of 16
相关PDF资料
PDF描述
OKY-T/16-W5N-C CONV DC/DC 52.8W 5VIN 16AOUT SMD
OSTVL143150 CONN TERM BLK HDR 14POS 3.81MM
OSTVL141151 CONN TERM BLK HEADER 14POS 3.5MM
OSTVL141150 CONN TERM BLK HEADER 14POS 3.5MM
MC74VHCT573ADW IC LATCH OCTAL D 3ST 20-SOICW
相关代理商/技术参数
参数描述
OKY-T 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:Adjustable Output 3 and 5-Amp DOSA-SMT PoLs
OKY-T/10 制造商:MURATA-PS 制造商全称:Murata Power Solutions Inc. 功能描述:Programmable DOSA-SMT 10/16-Amp DC/DC Converters
OKY-T/10-D12N-C 功能描述:DC/DC转换器 12Vin 0.7525-5.5Vout 10A 50W Neg Polarity RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压(标称): 输出端数量:1 输出电压(通道 1):3.3 V 输出电流(通道 1):600 mA 输出电压(通道 2): 输出电流(通道 2): 安装风格:SMD/SMT 封装 / 箱体尺寸:
OKY-T/10-D12P-C 功能描述:DC/DC转换器 12Vin 0.7525-5.5Vout 10A 50W Pos Polarity RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压(标称): 输出端数量:1 输出电压(通道 1):3.3 V 输出电流(通道 1):600 mA 输出电压(通道 2): 输出电流(通道 2): 安装风格:SMD/SMT 封装 / 箱体尺寸:
OKY-T/10-W5 制造商:Murata Power Solutions 功能描述:- Rail/Tube