参数资料
| 型号： | OP1177ARMZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/24页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP GP 1.3MHZ PREC LN 8MSOP |
| 产品培训模块： | Power Line Monitoring Top Five Instrumentation Amplifier Problems |
| 设计资源： | Versatile High Precision Programmable Current Sources Using DACs, Op Amps, and MOSFET Transistors (CN0151) How to Achieve High Precision Voltage Level Setting Using AD5541A/42A (CN0169) |
| 标准包装： | 50 |
| 放大器类型： | 通用 |
| 电路数： | 1 |
| 转换速率： | 0.7 V/µs |
| 增益带宽积： | 1.3MHz |
| 电流 - 输入偏压： | 500pA |
| 电压 - 输入偏移： | 15µV |
| 电流 - 电源： | 400µA |
| 电流 - 输出 / 通道： | 10mA |
| 电压 - 电源，单路/双路(±)： | 5 V ~ 36 V，±2.5 V ~ 18 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 管件 |
OP1177/OP2177/OP4177
Rev. G | Page 18 of 24
PROPER BOARD LAYOUT
The OPx177 is a high precision device. To ensure optimum
performance at the PCB level, care must be taken in the design
of the board layout.
To avoid leakage currents, the surface of the board should be
kept clean and free of moisture. Coating the surface creates a
barrier to moisture accumulation and helps reduce parasitic
resistance on the board.
Keeping supply traces short and properly bypassing the power
supplies minimizes power supply disturbances due to output
current variation, such as when driving an ac signal into a heavy
load. Bypass capacitors should be connected as closely as possible
to the device supply pins. Stray capacitances are a concern at the
outputs and the inputs of the amplifier. It is recommended that
signal traces be kept at least 5 mm from supply lines to
minimize coupling.
A variation in temperature across the PCB can cause a mismatch in
the Seebeck voltages at solder joints and other points where dissi-
milar metals are in contact, resulting in thermal voltage errors. To
minimize these thermocouple effects, orient resistors so heat
sources warm both ends equally. Input signal paths should contain
matching numbers and types of components, where possible to
match the number and type of thermocouple junctions. For
example, dummy components such as zero value resistors can
be used to match real resistors in the opposite input path.
Matching components should be located in close proximity and
should be oriented in the same manner. Ensure leads are of equal
length so that thermal conduction is in equilibrium. Keep heat
sources on the PCB as far away from amplifier input circuitry as
is practical.
The use of a ground plane is highly recommended. A ground
plane reduces EMI noise and also helps to maintain a constant
temperature across the circuit board.
DIFFERENCE AMPLIFIERS
Difference amplifiers are used in high accuracy circuits to improve
the common-mode rejection ratio (CMRR).
R1
V1
V2
R3 = R1
R4 = R1
OP1177
2
3
=
R4
R3
R2
R1
R2
100k
VOUT
02
62
7-
06
3
6
7
4
V+
V–
Figure 63. Difference Amplifier
In the single instrumentation amplifier (see Figure 63), where
R1
R2
R3
R4 =
()
1
2
O
V
R1
R2
V
=
a mismatch between the ratio R2/R1 and R4/R3 causes the
common-mode rejection ratio to be reduced.
To better understand this effect, consider that, by definition,
CM
DM
A
CMRR =
where ADM is the differential gain and ACM is the common-
mode gain.
CM
O
CM
DIFF
O
DM
V
A
V
A
and
=
()
2
1
CM
2
1
DIFF
V
+
=
=
2
1
and
For this circuit to act as a difference amplifier, its output must
be proportional to the differential input signal.
From Figure 63,
2
1
O
V
R4
R3
R1
R2
V
R1
R2
V
1
+
+
+
=
Arranging terms and combining the previous equations yields
R2R3
R4R1
R4R2
R3R2
R4R1
CMRR
2
+
=
(1)
The sensitivity of CMRR with respect to the R1 is obtained by
taking the derivative of CMRR, in Equation 1, with respect to R1.
+
δ
=
δ
R2R3
R1R4
R2R3
R2R4
R2R3
R1R4
R1
CMRR
2
()
R1R4
R2R3
R1
CMRR
2
1
=
δ
Assuming that
R1 ≈ R2 ≈ R3 ≈ R4 ≈ R
and
R(1 δ) < R1, R2, R3, R4 < R(1 + δ)
the worst-case CMRR error arises when
R1 = R4 = R(1 + δ) and R2 = R3 = R(1 δ)
相关PDF资料 |
PDF描述 |
|---|---|
| LTC6101CIS5#TRPBF | IC AMP CURRENT SENSE TSOT23-5 |
| LTC6101HVBCS5#TRPBF | IC AMP CURRENT SENSE TSOT23-5 |
| 6-534237-2 | CONN RECEPT 14POS .100 VERT GOLD |
| LTC6101CIS5#TRMPBF | IC AMP CURRENT SENSE TSOT23-5 |
| LT1993IUD-4#TRPBF | IC DIFF AMP/ADC DRVR 16-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| OP1177ARMZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:Precision Low Noise, Low Input Bias Current Operational Amplifiers |
| OP1177ARMZ-R | 制造商:Analog Devices 功能描述: |
| OP1177ARMZ-R2 | 制造商:Analog Devices 功能描述:OP Amp Single GP ±15V 8-Pin MSOP T/R |
| OP1177ARMZ-R7 | 功能描述:IC OPAMP GP 1.3MHZ PREC LN 8MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:160 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:10 V/µs 增益带宽积:9MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:250µV 电流 - 电源:730µA 电流 - 输出 / 通道:28mA 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:管件 |
| OP1177ARMZ-R71 | 制造商:AD 制造商全称:Analog Devices 功能描述:Precision Low Noise, Low Input Bias Current Operational Amplifiers |
发布紧急采购，3分钟左右您将得到回复。