参数资料
| 型号： | OP270GPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 6/20页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP GP 5MHZ DUAL PREC 8DIP |
| 标准包装： | 50 |
| 放大器类型： | 通用 |
| 电路数： | 2 |
| 转换速率： | 2.4 V/µs |
| 增益带宽积： | 5MHz |
| 电流 - 输入偏压： | 15nA |
| 电压 - 输入偏移： | 50µV |
| 电流 - 电源： | 4mA |
| 电压 - 电源，单路/双路(±)： | ±4.5 V ~ 18 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
| 产品目录页面： | 772 (CN2011-ZH PDF) |
OP270
Rev. E | Page 14 of 20
NOISE MEASUREMENTS
Peak-to-Peak Voltage Noise
The circuit of Figure 35 is a test setup for measuring peak-to-
peak voltage noise. To measure the 200 nV peak-to-peak noise
specification of the OP270 in the 0.1 Hz to 10 Hz range, the
following precautions must be observed:
The device has to be warmed up for at least five minutes.
As shown in the warm-up drift curve (see Figure 8), the
offset voltage typically changes 2 μV due to increasing chip
temperature after power-up. In the 10 sec measurement
interval, these temperature-induced effects can exceed tens
of nanovolts.
For similar reasons, the device has to be well shielded from
air currents. Shielding also minimizes thermocouple effects.
Sudden motion in the vicinity of the device can also feed
through to increase the observed noise.
The test time to measure noise of 0.1 Hz to 10 Hz should
not exceed 10 sec. As shown in the noise-tester frequency
response curve of Figure 36, the 0.1 Hz corner is defined by
only one pole. The test time of 10 sec acts as an additional
pole to eliminate noise contribution from the frequency
band below 0.1 Hz.
A noise voltage density test is recommended when measuring
noise on several units. A 10 Hz noise voltage density mea-
surement correlates well with a 0.1 Hz to 10 Hz peak-to-peak
noise reading because both results are determined by the
white noise and the location of the 1/f corner frequency.
Power should be supplied to the test circuit by well bypassed
low noise supplies, such as batteries. Such supplies will min-
imize output noise introduced via the amplifier supply pins.
00
35
2-
0
37
100
60
80
0
20
40
GA
IN
(
d
B
)
FREQUENCY (Hz)
0.01
0.1
1
10
100
Figure 36. 0.1 Hz to 10 Hz Peak-to-Peak Voltage Noise
Test Circuit Frequency Response
Noise Measurement—Noise Voltage Density
The circuit of Figure 37 shows a quick and reliable method for
measuring the noise voltage density of dual op amps. The first
amplifier is in unity gain, with the final amplifier in a noninverting
gain of 101. Because the noise voltages of the amplifiers are
uncorrelated, they add in rms to yield
( ) ( )
(
)2
2
101
nB
nA
OUT
e
+
=
The OP270 is a monolithic device with two identical amplifiers.
Therefore, the noise voltage densities of the amplifiers match,
giving
(
) ( )
n
OUT
e
2
101
2
101
2
=
00
32
5-
0
38
eOUT (nV/√Hz) ≈ 101 (√2en)
VS = ±15V
TO SPECTRUM ANALYZER
eOUT
R1
100
R2
10k
1/2
OP270
1/2
OP270
Figure 37. Noise Voltage Density Test Circuit
Noise Measurement—Current Noise Density
The test circuit shown in Figure 38 can be used to measure current
noise density. The formula relating the voltage output to the current
noise density is
()
S
nOUT
n
R
Hz
nV
G
e
i
2
/
40
=
where:
G is a gain of 10,000.
RS = 100 kΩ source resistance.
00
32
5-
0
39
OP270
DUT
R1
5
R2
100k
R3
1.24k
OP27E
R5
8.06k
R4
200
enOUT
GAIN = 10,000
VS = ±15V
TO SPECTRUM ANALYZER
Figure 38. Current Noise Density Test Circuit
相关PDF资料 |
PDF描述 |
|---|---|
| AD8622ARZ-REEL7 | IC OPAMP GP R-R 540KHZ LP 8SOIC |
| AD820BRZ | IC OPAMP JFET R-R 1.8MHZ 8SOIC |
| AD8011ANZ | IC OPAMP CF LP LDIST 30MA 8DIP |
| AD8011ARZ | IC OPAMP CF LP LDIST 30MA 8SOIC |
| LTC2051HVCDD#PBF | IC OP AMP ZERO-DRIFT DUAL 8-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| OP270GPZ2 | 制造商:AD 制造商全称:Analog Devices 功能描述:Dual Very Low Noise Precision Operational Amplifier |
| OP270GS | 功能描述:IC OPAMP GP 5MHZ DUAL LN 16SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:J-FET 电路数:2 输出类型:- 转换速率:3.5 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:30pA 电压 - 输入偏移:2000µV 电流 - 电源:200µA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-PDIP 包装:管件 |
| OP-270GS | 制造商:AD 制造商全称:Analog Devices 功能描述:DUAL VERY LOW NOISE PRECISION OPERATIONAL AMPLIFIER |
| OP270GS-REEL | 功能描述:IC OPAMP GP 5MHZ DUAL LN 16SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.028 V/µs 增益带宽积:105kHz -3db带宽:- 电流 - 输入偏压:3nA 电压 - 输入偏移:100µV 电流 - 电源:3.3µA 电流 - 输出 / 通道:12mA 电压 - 电源，单路/双路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:剪切带 (CT) 其它名称:OP481GRUZ-REELCT |
| OP270GSZ | 功能描述:IC OPAMP GP 5MHZ DUAL LN 16SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.6 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:45nA 电压 - 输入偏移:2000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:40mA 电压 - 电源，单路/双路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) 其它名称:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
发布紧急采购，3分钟左右您将得到回复。