- 您现在的位置：买卖IC网 > PDF目录296740 > OP296GSZ-REEL7 (ANALOG DEVICES INC) Micropower, Rail-to-Rail Input and Output Operational Amplifiers; Package: SOIC; No of Pins: 8; Temperature Range: Industrial PDF资料下载
参数资料
| 型号： | OP296GSZ-REEL7 |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | 运算放大器 |
| 英文描述： | Micropower, Rail-to-Rail Input and Output Operational Amplifiers; Package: SOIC; No of Pins: 8; Temperature Range: Industrial |
| 中文描述： | DUAL OP-AMP, 650 uV OFFSET-MAX, 0.35 MHz BAND WIDTH, PDSO8 |
| 封装： | ROHS COMPLIANT, MS-012AA, SOIC-8 |
| 文件页数： | 5/19页 |
| 文件大小： | 2367K |
| 代理商： | OP296GSZ-REEL7 |
OP196/OP296/OP496
REV.
–13–
A Micropower False-Ground Generator
Some single supply circuits work best when inputs are biased
above ground, typically at 1/2 of the supply voltage. In these
cases, a false-ground can be created by using a voltage divider
buffered by an amplifier. One such circuit is shown in Figure 5.
This circuit will generate a false-ground reference at 1/2 of the
supply voltage, while drawing only about 55
A from a 5 V
supply. The circuit includes compensation to allow for a 1
F
bypass capacitor at the false-ground output. The benefit of a
large capacitor is that not only does the false-ground present a
very low dc resistance to the load, but its ac impedance is low as well.
6
2
3
10k
OP196
100
4
5V OR 12V
0.022 F
1 F
240k
1 F
2.5V OR 6V
7
Figure 5. A Micropower False-Ground Generator
Single-Supply Half-Wave and Full-Wave Rectifiers
An OP296, configured as a voltage follower operating from a
single supply, can be used as a simple half-wave rectifier in low
frequency (<400 Hz) applications. A full-wave rectifier can be
configured with a pair of OP296s as illustrated in Figure 6.
A1
8
1
3
4
5V
1/2
OP296
2k
2
A2
5
6
2Vp-p
<500Hz
7
1/2
OP296
R1
100k
R2
100k
VOUTA
FULL-WAVE
RECTIFIED
OUTPUT
VOUTB
HALF-WAVE
RECTIFIED
OUTPUT
10
0%
100
90
500mV
1V
500s
500mV
f = 500Hz
INPUT
VOUTB
(HALF-WAVE
OUTPUT)
VOUTA
(FULL-WAVE
OUTPUT)
Figure 6. Single-Supply Half-Wave and Full-Wave
Rectifiers Using an OP296
The circuit works as follows: When the input signal is above
0 V, the output of amplifier A1 follows the input signal. Since
the noninverting input of amplifier A2 is connected to A1’s
output, op amp loop control forces A2’s inverting input to the
same potential. The result is that both terminals of R1 are at the
same potential and no current flows in R1. Since there is no
current flow in R1, the same condition must exist in R2; thus,
the output of the circuit tracks the input signal. When the input
signal is below 0 V, the output voltage of A1 is forced to 0 V.
This condition now forces A2 to operate as an inverting voltage
follower because the noninverting terminal of A2 is also at 0 V.
The output voltage of VOUTA is then a full-wave rectified
version of the input signal. A resistor in series with A1’s
noninverting input protects the ESD diodes when the input
signal goes below ground.
Square Wave Oscillator
The oscillator circuit in Figure 7 demonstrates how a rail-to-rail
output swing can reduce the effects of power supply variations
on the oscillator’s frequency. This feature is especially valuable
in battery powered applications, where voltage regulation may
not be available. The output frequency remains stable as the
supply voltage changes because the RC charging current, which
is derived from the rail-to-rail output, is proportional to the
supply voltage. Since the Schmitt trigger threshold level is also
proportional to supply voltage, the frequency remains relatively
independent of supply voltage. For a supply voltage change
from 9 V to 5 V, the output frequency only changes about 4 Hz.
The slew rate of the amplifier limits the oscillation frequency to
a maximum of about 200 Hz at a supply voltage of 5 V.
59k
1/2
OP296/
OP496
100k
FREQ OUT
fOSC =
< 200Hz @ V+ = 5V
1
RC
C
V+
R
2
3
4
8
1
Figure 7. Square Wave Oscillator Has Stable Frequency
Regardless of Supply Voltage Changes
A 3 V Low Dropout, Linear Voltage Regulator
Figure 8 shows a simple 3 V voltage regulator design. The regu-
lator can deliver 50 mA load current while allowing a 0.2 V
dropout voltage. The OP296’s rail-to-rail output swing easily
drives the MJE350 pass transistor without requiring special
drive circuitry. With no load, its output can swing to less than
the pass transistor’s base-emitter voltage, turning the device
nearly off. At full load, and at low emitter-collector voltages, the
transistor beta tends to decrease. The additional base current is
easily handled by the OP296 output.
The AD589 provides a 1.235 V reference voltage for the regula-
tor. The OP296, operating with a noninverting gain of 2.43,
drives the base of the MJE350 to produce an output voltage of
3.0 V. Since the MJE350 operates in an inverting (common-
emitter) mode, the output feedback is applied to the OP296’s
noninverting input.
E
相关PDF资料 |
PDF描述 |
|---|---|
| OP296HRUZ-REEL | Micropower, Rail-to-Rail Input and Output Operational Amplifiers; Package: TSSOP; No of Pins: 8; Temperature Range: Industrial |
| OP297FPZ | Dual Low Bias Current Precision Operational Amplifier; Package: PDIP; No of Pins: 8; Temperature Range: Industrial |
| OP297FSZ | Dual Low Bias Current Precision Operational Amplifier; Package: SOIC; No of Pins: 8; Temperature Range: Industrial |
| OP297FSZ-REEL | Dual Low Bias Current Precision Operational Amplifier; Package: SOIC; No of Pins: 8; Temperature Range: Industrial |
| OP297FSZ-REEL7 | Dual Low Bias Current Precision Operational Amplifier; Package: SOIC; No of Pins: 8; Temperature Range: Industrial |
相关代理商/技术参数 |
参数描述 |
|---|---|
| OP296HRU | 制造商:AD 制造商全称:Analog Devices 功能描述:Micropower, Rail-to-Rail Input and Output Operational Amplifiers |
| OP296HRU-REEL | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:IC OP-AMP R/R 制造商:Analog Devices 功能描述:IC,Operational Amplifier,DUAL,BICMOS,TSSOP,8PIN,PLASTIC |
| OP296HRUZ-REEL | 功能描述:IC OPAMP DUAL R-R MCRPWR 8-TSSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Differential Circuit Design Techniques for Communication Applications 标准包装:1 系列:- 放大器类型:RF/IF 差分 电路数:1 输出类型:差分 转换速率:9800 V/µs 增益带宽积:- -3db带宽:2.9GHz 电流 - 输入偏压:3µA 电压 - 输入偏移:- 电流 - 电源:40mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-VQFN 裸露焊盘，CSP 供应商设备封装:16-LFCSP-VQ 包装:剪切带 (CT) 产品目录页面:551 (CN2011-ZH PDF) 其它名称:ADL5561ACPZ-R7CT |
| OP297 | 制造商:AD 制造商全称:Analog Devices 功能描述:Dual Low Bias Current Precision Operational Amplifier |
| OP-297 | 制造商:AD 制造商全称:Analog Devices 功能描述:DUAL LOW BIAS CURRENT PRECISION OPERATIONAL AMPLIFIER |
发布紧急采购，3分钟左右您将得到回复。