- 您现在的位置：买卖IC网 > Datasheet目录697 > OP4009B (RFM)IC OPT TIME CLK 672.163MHZ 8-SMC Datasheet资料下载
参数资料
| 型号： | OP4009B |
| 厂商： | RFM |
| 文件页数： | 1/3页 |
| 文件大小： | 0K |
| 描述： | IC OPT TIME CLK 672.163MHZ 8-SMC |
| 标准包装： | 200 |
| 类型： | VCSO（SAW） |
| 频率： | 672.163MHz |
| 功能： | 三态（输出启用） |
| 电源电压： | 3.13V ~ 5.25V |
| 频率稳定性： | ±100ppm |
| 工作温度： | -40°C ~ 85°C |
| 电流 - 电源（最大）： | 70mA |
| 安装类型： | 表面贴装 |
| 尺寸/尺寸： | 0.530" L x 0.360" W（13.46mm x 9.14mm） |
| 高度： | 0.076"（1.93mm） |
| 封装/外壳： | 8-SMD |
| 包装： | 带卷 (TR) |
?
?
?
?
?
Quartz SAW Stabilized and Filtered “Diff Sine” Technology
Fundamental-Mode Oscillation at 672.163 MHz
Voltage Tunable for Phase Lock Loop Operations
Optical Timing Reference for Forward Error Correction Applications
Complies with Directive 2002/95/EC (RoHS)
2 >
OP4009B
672.163 MHz
Optical
The output of this device is generated and filtered by narrowband quartz SAW elements at 672.163 MHz. The
configuration of this clock is intended to provide a pure signal for optical timing applications in noisy signal
environments. The Q/Qbar differential output swing of ±1 volt about 0 Vdc has symmetry better than ±1% into
loads from 40 to 70 ohms; determined by customer application. The long term frequency accuracy is set by
an external reference source allowing this device to complete a Phase Lock Loop design without the usual
noise and jitter problems associated with PLL’s.
Absolute Maximum Ratings
Timing Clock
Rating
DC Suppy Voltage
Tuning Voltage
Value
0 to 5.5
0 to 5.5
Units
Vdc
Vdc
Case Temperature
-55 to 100
°C
SMC-08
Electrical Characteristics
Characteristic
Operating Frequency
Absolute Frequency
Sym
f O
Notes
1, 9
Minimum
Typical
672.163
Maximum
Units
MHz
Tuning Range
2
±100
ppm
Tuning Voltage
Tuning Linearity
1
1, 8
0
±3
+3
±5
V
%
Tuning Sensitivity
Modulation Bandwidth
Q and Q Output Voltage into 50 ? (VSWR ≤ 1.2)
df/dv
V O
2, 10
1,3
140
125
0.60
265
300
1.1
ppm/V
kHz
V P-P
Operating Load VSWR
1,3
2:1
Symmetry
Harmonic Spurious
Nonharmonic Spurious
Phase Noise @100 Hz offset
@1 kHz offset
@10 kHz offset
Noise Floor
Q and Q Jitter RMS Jitter
No Noise on V CC
200 mV P-P from 1 MHz to ? f O on
Input Impedance (Tuning Port)
Output DC Resistance (between Q & Q)
3, 4, 5
3, 4, 6
3, 4, 6, 7
3, 4, 6, 7
3, 4, 6, 7
3
1, 3
49
1
50
-75
-105
-125
-155
2
12
12
51
-30
-60
%
dBc
dBc
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
ps P-P
ps P-P
ps P-P
K ?
K ?
DC Power Supply Operating Voltage
Operating Current
Operating Case Temperature
V CC
I CC
T C
1, 3
1, 3
1, 3
3.13
-40
3.3, 5.0
5.25
70
+85
Vdc
mA
°C
Lid Symbolization (YY=Year, WW=Week)
RFM OP4009B YYWW
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
COCOM CAUTION: Approval by the U.S. Department of Commerce is required prior to export of this device.
Notes:
1. Unless otherwise noted, all specifications include any combination of load VSWR, Vcc, and temperature, with Q and Q terminated into 50 ohm loads
to ground (see typical test circuit).
2. Useful tuning range is in excess of what is required over temp, aging, pushing, pulling & accuracy.
3. The design, manufacturing process, and specifications of this device are subject to change without notice.
4. Only under the nominal conditions of 50 ? load impedance with VSWR ≤ 1.2 and nominal power supply voltage.
5. Symmetry is defined as the pulse width (in percent of total period) measured at the 50% points of Q or Q (see timing definitions).
6. Jitter and other spurious outputs induced by externally generated electrical noise on V CC or mechanical vibration are not included in this
specification, except where noted. External voltage regulation and careful PCB layout are recommended for optimum performance.
7. Applies to period jitter of Q and Q. Measurements are made with the Tektronix CSA803 signal analyzer with at least 1000 samples.
8. Linearity is a function of the percentage variation from a permitted linear deviation versus the amount of frequency tuning range (see linearity
definition).
9. One or more of the following United States patents apply: 4,616,197; 4,670,681; 4,760,352.
www.RFM.com E-mail: info@rfm.com
?2008-2010 by RF Monolithics, Inc.
Page 1 of 3
OP4009B - 2/8/10
相关PDF资料 |
PDF描述 |
|---|---|
| OP4010B | IC OPT TIME CLK 663.552MHZ 8-SMC |
| OP4011B | IC OPT TIME CLK 719.734MHZ 8-SMC |
| OP4012B | IC OPT TIMECLK 644.53125MHZ 8SMC |
| OP4013B | IC OPT TIMECLK 693.48342MHZ 8SMC |
| OP4014B | IC OPT TIME CLK 627.329MHZ 8-SMC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| OP400ATC | 制造商:AD 制造商全称:Analog Devices 功能描述:Quad Low Offset, Low Power Operational Amplifier |
| OP-400ATC/883 | 制造商:AD 制造商全称:Analog Devices 功能描述:QUAD LOW-OFFSET, LOW-POWER OPERATIONAL AMPLIFIER |
| OP400ATCMDA | 制造商:AD 制造商全称:Analog Devices 功能描述:Quad Low Offset, Low Power Operational Amplifier |
| OP400AY | 功能描述:IC OPAMP GP 500KHZ QUAD 14CDIP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:J-FET 电路数:2 输出类型:- 转换速率:3.5 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:30pA 电压 - 输入偏移:2000µV 电流 - 电源:200µA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-PDIP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。