- 您现在的位置：买卖IC网 > PDF目录5786 > OP4177ARU-REEL (Analog Devices Inc)IC OPAMP GP 1.3MHZ QUAD 14TSSOP PDF资料下载
参数资料
| 型号： | OP4177ARU-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/24页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP GP 1.3MHZ QUAD 14TSSOP |
| 标准包装： | 2,500 |
| 放大器类型： | 通用 |
| 电路数： | 4 |
| 转换速率： | 0.7 V/µs |
| 增益带宽积： | 1.3MHz |
| 电流 - 输入偏压： | 500pA |
| 电压 - 输入偏移： | 15µV |
| 电流 - 电源： | 400µA |
| 电流 - 输出 / 通道： | 10mA |
| 电压 - 电源，单路/双路(±)： | 5 V ~ 36 V，±2.5 V ~ 18 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 14-TSSOP |
| 包装： | 带卷 (TR) |
OP1177/OP2177/OP4177
Rev. G | Page 19 of 24
Plugging these values into Equation 1 yields
δ
2
1
MIN
CMRR
where δ is the tolerance of the resistors.
Lower tolerance value resistors result in higher common-mode
rejection (up to the CMRR of the operational amplifier).
Using 5% tolerance resistors, the highest CMRR that can be
guaranteed is 20 dB. Alternatively, using 0.1% tolerance resistors
results in a common-mode rejection ratio of at least 54 dB
(assuming that the operational amplifier CMRR × 54 dB).
With the CMRR of OPx177 at 120 dB minimum, the resistor
match is the limiting factor in most circuits. A trimming resistor
can be used to further improve resistor matching and CMRR of
the difference amplifier circuit.
A HIGH ACCURACY THERMOCOUPLE AMPLIFIER
A thermocouple consists of two dissimilar metal wires placed in
contact. The dissimilar metals produce a voltage
VTC = α(TJ TR)
where:
TJ is the temperature at the measurement of the hot junction.
TR is the temperature at the cold junction.
α is the Seebeck coefficient specific to the dissimilar metals used
in the thermocouple.
VTC is the thermocouple voltage and becomes larger with
increasing temperature.
Maximum measurement accuracy requires cold junction compen-
sation of the thermocouple. To perform the cold junction compen-
sation, apply a copper wire short across the terminating junctions
(inside the isothermal block) simulating a 0°C point. Adjust the
output voltage to zero using the R5 trimming resistor, and remove
the copper wire.
The OPx177 is an ideal amplifier for thermocouple circuits
because it has a very low offset voltage, excellent PSRR and
CMRR, and low noise at low frequencies.
It can be used to create a thermocouple circuit with great
linearity. Resistor R1, Resistor R2, and Diode D1, shown in
Figure 64, are mounted in an isothermal block.
V+
7
4
Cu
TR
D1
ADR293
VCC
C1
2.2F
R3
47k
10F
R2
4.02k
R8
1k
R7
80.6k
R6
50
R9
200k
0.1F
10F
0.1F
10F
V–
10F
R4
50
R5
100
R1
50
ISOTHERMAL
BLOCK
VTC
TJ
(–)
(+)
6
2
3
OP1177
VOUT
0262
7-
064
Figure 64. Type K Thermocouple Amplifier Circuit
LOW POWER LINEARIZED RTD
A common application for a single element varying bridge is an
RTD thermometer amplifier, as shown in Figure 65. The excita-
tion is delivered to the bridge by a 2.5 V reference applied at the
top of the bridge.
RTDs may have thermal resistance as high as 0.5°C to 0.8°C
per mW. To minimize errors due to resistor drift, the current
through each leg of the bridge must be kept low. In this circuit,
the amplifier supply current flows through the bridge. However,
at the OPx177 maximum supply current of 600 μA, the RTD
dissipates less than 0.1 mW of power, even at the highest resis-
tance. Errors due to power dissipation in the bridge are kept
under 0.1°C.
Calibration of the bridge is made at the minimum value of
temperature to be measured by adjusting RP until the output is zero.
To calibrate the output span, set the full-scale and linearity
potentiometers to midpoint and apply a 500°C temperature to
the sensor or substitute the equivalent 500°C RTD resistance.
Adjust the full-scale potentiometer for a 5 V output. Finally,
apply 250°C or the equivalent RTD resistance and adjust the
linearity potentiometer for 2.5 V output. The circuit achieves
better than ±0.5°C accuracy after adjustment.
相关PDF资料 |
PDF描述 |
|---|---|
| 961128-6804-AR | CONN HEADER VERT SGL 28POS GOLD |
| 961228-6404-AR | CONN HEADER VERT DUAL 28POS GOLD |
| 0603SFF075F/32-2 | FUSE 0.75A 32V FAST SMD 0603 |
| 0603SFF050F/32-2 | FUSE 0.50A 32V FAST SMD 0603 |
| 170M5411 | FUSE 550A 690V 2BN/50 AR UC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| OP4177ARUZ | 功能描述:IC OPAMP GP 1.3MHZ QUAD 14TSSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.6 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:45nA 电压 - 输入偏移:2000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:40mA 电压 - 电源，单路/双路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) 其它名称:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| OP4177ARUZ | 制造商:Analog Devices 功能描述:Operational Amplifier (Op-Amp) IC |
| OP4177ARUZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:Precision Low Noise, Low Input Bias Current Operational Amplifiers |
| OP4177ARUZ-REEL | 功能描述:IC OPAMP GP 1.3MHZ QUAD 14TSSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:73 系列:Over-The-Top® 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.07 V/µs 增益带宽积:200kHz -3db带宽:- 电流 - 输入偏压:1nA 电压 - 输入偏移:285µV 电流 - 电源:50µA 电流 - 输出 / 通道:25mA 电压 - 电源，单路/双路(±):2 V ~ 44 V，±1 V ~ 22 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-WFDFN 裸露焊盘 供应商设备封装:16-DFN-EP（5x3） 包装:管件 |
| OP4177ARUZ-REEL1 | 制造商:AD 制造商全称:Analog Devices 功能描述:Precision Low Noise, Low Input Bias Current Operational Amplifiers |
发布紧急采购，3分钟左右您将得到回复。