参数资料
| 型号： | OP492GS-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 5/20页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP GP 4MHZ QUAD 14SOIC |
| 标准包装： | 2,500 |
| 放大器类型： | 通用 |
| 电路数： | 4 |
| 转换速率： | 4 V/µs |
| 增益带宽积： | 4MHz |
| 电流 - 输入偏压： | 375nA |
| 电压 - 输入偏移： | 1400µV |
| 电流 - 电源： | 1mA |
| 电流 - 输出 / 通道： | 10.5mA |
| 电压 - 电源，单路/双路(±)： | 4.5 V ~ 33 V，±2.25 V ~ 16.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 14-SOIC |
| 包装： | 带卷 (TR) |
OP292/OP492
Rev. C | Page 13 of 20
APPLICATIONS INFORMATION
PHASE REVERSAL
The OP492 has built-in protection against phase reversal when
the input voltage goes to either supply rail. In fact, it is safe for
the input to exceed either supply rail by up to 0.6 V with no risk
of phase reversal. However, the input should not go beyond the
positive supply rail by more than 0.9 V; otherwise, the output
will reverse phase. If this condition occurs, the problem can be
fixed by adding a 5 kΩ current limiting resistor in series with
the input pin. With this addition, the input can go to more than
5 V beyond the positive rail without phase reversal.
An input voltage that is as much as 5 V below the negative rail
will not result in phase reversal.
OP492
2k
5V
0V
11.8V p-p
1V
90
100
10
5s
0%
00
310
-03
4
Figure 34. Output Phase Reverse If Input Exceeds
the Positive Supply (V+) by More Than 0.9 V
2k
5V
0V
10V p-p
1V/DIV
OP492
00
31
0-
03
5
4ms/DIV
Figure 35. No Negative Rail Phase Reversal, Even with Input Signal
at 5 V Below Ground
POWER SUPPLY CONSIDERATIONS
The OP292/OP492 are designed to operate equally well at single
+5 V or ±15 V supplies. The lowest supply voltage recommended
is 4.5 V.
It is a good design practice to bypass the supply pins with a
0.1 μF ceramic capacitor. It helps improve filtering of high
frequency noise.
For dual-supply operation, the negative supply (V) must be
applied at the same time, or before V+. If V+ is applied before V,
or in the case of a loss of the V supply, while either input is
connected to ground or another low impedance source, excessive
input current may result. Potentially damaging levels of input
current can destroy the amplifier. If this condition can exist,
simply add a l kΩ or larger resistor in series with the input to
eliminate the problem.
相关PDF资料 |
PDF描述 |
|---|---|
| 929665-08-12-I | CONN HEADER .100 DUAL STR 24POS |
| 951204-7722-AR | CONN HEADER 4POS 2MM R/A SOLDER |
| 3412.0117.22 | FUSE 1.5A 32V 0603 FAST SMD |
| 951104-7722-AR | CONN HEADER 4POS 2MM R/A SOLDER |
| 69190-208HLF | BERGSTIK II SR STRAIGHT RET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| OP492GS-REEL7 | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| OP492GSZ | 功能描述:IC OPAMP GP 4MHZ QUAD 14SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.6 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:45nA 电压 - 输入偏移:2000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:40mA 电压 - 电源，单路/双路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) 其它名称:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| OP492GSZ-REEL | 功能描述:IC OPAMP GP 4MHZ QUAD 14SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:100 系列:- 放大器类型:通用 电路数:1 输出类型:- 转换速率:0.2 V/µs 增益带宽积:- -3db带宽:- 电流 - 输入偏压:100pA 电压 - 输入偏移:30µV 电流 - 电源:380µA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):±2 V ~ 18 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SO 包装:管件 |
| OP493 | 制造商:AD 制造商全称:Analog Devices 功能描述:Precision, Micropower Operational Amplifiers |
| OP4930003SR | 制造商:Analog Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。