- 您现在的位置：买卖IC网 > PDF目录189407 > OPA2334AIDGSRG4 (TEXAS INSTRUMENTS INC) DUAL OP-AMP, 5 uV OFFSET-MAX, 2 MHz BAND WIDTH, PDSO10 PDF资料下载
参数资料
| 型号： | OPA2334AIDGSRG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 运算放大器 |
| 英文描述： | DUAL OP-AMP, 5 uV OFFSET-MAX, 2 MHz BAND WIDTH, PDSO10 |
| 封装： | GREEN, PLASTIC, MSOP-10 |
| 文件页数： | 28/30页 |
| 文件大小： | 1094K |
| 代理商： | OPA2334AIDGSRG4 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页
7
www.ti.com
OPA334, OPA2334, OPA335, OPA2335
SBOS245D
TYPICAL CHARACTERISTICS (Cont.)
At TA = +25°C, VS = +5V, RL = 10k connected to VS /2, and VOUT = VS /2, unless otherwise noted.
APPLICATIONS INFORMATION
The OPA334 and OPA335 series op amps are unity-gain
stable and free from unexpected output phase reversal. They
use auto-zeroing techniques to provide low offset voltage
and very low drift over time and temperature.
Good layout practice mandates use of a 0.1
F capacitor
placed closely across the supply pins.
For lowest offset voltage and precision performance, circuit
layout and mechanical conditions should be optimized. Avoid
temperature gradients that create thermoelectric (Seebeck)
effects in thermocouple junctions formed from connecting
dissimilar conductors. These thermally-generated potentials
can be made to cancel by assuring that they are equal on
both input terminals.
Use low thermoelectric-coefficient connections (avoid dis-
similar metals).
Thermally isolate components from power supplies or
other heat-sources.
Shield op amp and input circuitry from air currents, such as
cooling fans.
Following these guidelines will reduce the likelihood of junc-
tions being at different temperatures, which can cause ther-
moelectric voltages of 0.1
V/°C or higher, depending on
materials used.
OPERATING VOLTAGE
The OPA334 and OPA335 series op amps operate over a
power-supply range of +2.7V to +5.5V (
±1.35V to ±2.75V).
Supply voltages higher than 7V (absolute maximum) can
permanently damage the amplifier. Parameters that vary
over supply voltage or temperature are shown in the Typical
Characteristics section of this data sheet.
OPA334 ENABLE FUNCTION
The enable/shutdown digital input is referenced to the V–
supply voltage of the amp. A logic high enables the op amp. A
valid logic high is defined as > 75% of the total supply voltage.
The valid logic high signal can be up to 5.5V above the negative
supply, independent of the positive supply voltage. A valid
logic low is defined as < 0.8V above the V– supply pin. If dual
or split power supplies are used, be sure that logic input signals
are properly referred to the negative supply voltage. The
Enable pin must be connected to a valid high or low voltage, or
driven, not left open circuit.
The logic input is a high-impedance CMOS input, with sepa-
rate logic inputs provided on the dual version. For battery-
operated applications, this feature can be used to greatly
reduce the average current and extend battery life.
The enable time is 150
s, which includes one full auto-zero
cycle required by the amplifier to return to VOS accuracy.
Prior to this time, the amplifier functions properly, but with
unspecified offset voltage.
Disable time is 1
s. When disabled, the output assumes a
high-impedance state. This allows the OPA334 to be oper-
ated as a gated amplifier, or to have the output multiplexed
onto a common analog output bus.
INPUT VOLTAGE
The input common-mode range extends from (V–) – 0.1V to
(V+) – 1.5V. For normal operation, the inputs must be limited
to this range. The common-mode rejection ratio is only valid
within the valid input common-mode range. A lower supply
voltage results in lower input common-mode range; there-
fore, attention to these values must be given when selecting
the input bias voltage. For example, when operating on a
single 3V power supply, common-mode range is from 0.1V
below ground to half the power-supply voltage.
COMMON-MODE RANGE vs SUPPLY VOLTAGE
Common-Mode
Range
(V)
2.7
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
–0.5
3.7
3.2
5.2
5.5
Supply Voltage (V)
4.7
4.2
Minimum Common-Mode
Maximum Common-Mode
SETTLING TIME vs CLOSED-LOOP GAIN
Settling
Time
(
s)
1
100
10
1
10
Gain (V/V)
100
0.1%
0.01%
Unity-gain
requires one
complete Auto-Zero
Cycle—see text.
相关PDF资料 |
PDF描述 |
|---|---|
| OPA2337UAG4 | DUAL OP-AMP, 3500 uV OFFSET-MAX, 3 MHz BAND WIDTH, PDSO8 |
| OPA2337UA | DIODE ZENER TRIPLE ISOLATED 200mW 39Vz 2mA-Izt 0.0513 0.1uA-Ir 27.3 SOT-363 3K/REEL |
| OPA237UA | DIODE ZENER SINGLE 300mW 39Vz 2mA-Izt 0.0513 0.1uA-Ir 27.3 SOT-23 3K/REEL |
| OPA337UA | DIODE ZENER SINGLE 150mW 39Vz 2mA-Izt 0.0513 0.1uA-Ir 27.3 SOT-523 3K/REEL |
| OPA338NA | MicroSIZE, Single-Supply CMOS OPERATIONAL AMPLIFIERS MicroAmplifier ⑩ Series |
相关代理商/技术参数 |
参数描述 |
|---|---|
| OPA2334AIDGST | 功能描述:运算放大器 - 运放 0.05uV/C max Single-Supply CMOS RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| OPA2334AIDGSTG4 | 功能描述:运算放大器 - 运放 0.05uV/C max Single-Supply CMOS RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| OPA2335 | 制造商:BB 制造商全称:BB 功能描述:0.05 mV/∑C MAX, SINGLE-SUPPLY CMOS OPERATIONAL AMPLIFIER ZERO-DRIFT SERIES |
| OPA2335AID | 功能描述:运算放大器 - 运放 0.05uV/C max Single-Supply CMOS RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| OPA2335AID | 制造商:Texas Instruments 功能描述:IC OP AMP DUAL SMD SOIC8 制造商:Texas Instruments 功能描述:IC, OP AMP, DUAL, SMD, SOIC8 制造商:Texas Instruments 功能描述:IC, OP AMP, DUAL, SMD, SOIC8; Op Amp Type:Zero Drift; No. of Amplifiers:2; Slew Rate:1.6V/s; Supply Voltage Range: 1.35V to 2.75V; Amplifier Case Style:SOIC; No. of Pins:8; Bandwidth:2MHz; Operating Temperature Min:-40C; ;RoHS Compliant: Yes |
发布紧急采购，3分钟左右您将得到回复。