- 您现在的位置：买卖IC网 > PDF目录21877 > OPB350W250Z (TT Electronics/Optek Technology)SENS OPTO SLOT 6.35MM TRANS C-MT PDF资料下载
参数资料
| 型号： | OPB350W250Z |
| 厂商： | TT Electronics/Optek Technology |
| 文件页数： | 6/8页 |
| 文件大小： | 0K |
| 描述： | SENS OPTO SLOT 6.35MM TRANS C-MT |
| 产品培训模块： | OPB350 Medical Applications |
| 产品目录绘图： | OPB350W Series |
| 标准包装： | 1 |
| 检测距离： | 0.250"（6.35mm） |
| 检测方法： | 液体 |
| 输出配置： | 光电晶体管 |
| 电流 - DC 正向(If)： | 50mA |
| 电流 - 集电极 (Ic)（最大）： | 50mA |
| 电压 - 集电极发射极击穿（最大）： | 30V |
| 安装类型： | 底座安装 |
| 封装/外壳： | 模块，预接线 |
| 包装： | 散装 |
| 工作温度： | -40°C ~ 85°C |
| 产品目录页面： | 2788 (CN2011-ZH PDF) |
| 其它名称： | 365-1240 |
Tube Liquid Sensor
OPB350 / OCB350 Series
(Calibration Circuit Available)
Calibration Circuit theory of operation:
The OCB350 series is designed to minimize the change of optical devices due to manufacturing variance. With the calibration
circuit, the design engineer can narrow the initial output state providing a device that will operate the same for years with the
same startup state thus enhancing the reliability and consistence of the system. Degradation of the LED or phototransistor is
compensated for each time the system is calibrated allowing the system to provide a known, consistent output level resulting
in years of consistent quality. The OCB350 series are designed to maintain the calibrated setting even if power is lost. This
allows faster startup without the need for calibration every time the device is initiated. The designer can initiate the calibration
procedure at any time by momentarily grounding J1-Pin-4 (green wire). This allows the device to be remotely calibrated then
mounted in the equipment.
The PCBoard has a set of shorting pins allowing the user to change the phototransistor load resistor. By arranging the
shorting bar to the appropriate location (see table), the load resistance can be changed from approximately 2.5K to 27 K Ω.
Increasing the load resistor increases the sensitivity of the device.
When the “Calibrate” pin (#4) is momentarily grounded, the system begins its calibration process and raises the current
through the LED, from 0 mA to 14 mA, until the phototransistor reaches the preset calibration point. A green calibration light
will blink during the initiation and will stop when the preset phototransistor output level is reached. At this time, the LED
drive current is locked and maintained until Reset/Clear pin is momentarily grounded. If for some reason, the LED drive
current reaches the maximum allowable value, a RED warning light will be turned on. During the calibration process, remote
monitoring of J1-Pin3 allows the designer to ensure the system is calibrated (this output should be at the preset calibrated
output level when the calibration procedure is completed). The phototransistor load resistor may need to be adjusted to allow
the system to calibrate properly.
After the calibration process is complete, the device is ready for acknowledgement of a change in the signal. The design
engineer can monitor either the Analog Output (J1-Pin 5) or Logical Output (J1-Pin 2 or J1-Pin 3).
The Logical output will change state once the preset optical light condition is reached. The “Logic Out A” switches when the
optical signal increases above approximately 2/3 of V CC while “Logic Out B” switches when the optical signal decreases
below approximately 1/3 of V CC .
As with all optical devices, the switching condition is consistent with the phototransistor receiving a preset light level. This
switching position and light level may vary dependent on several possible factors such as:
?
?
?
?
?
Ambient light variation ((reduced or eliminated with periodic recalibration)
LED and phototransistor pair degradation (eliminated with periodic recalibration)
Contamination in front of either the LED or phototransistor (reduced or eliminated with periodic cleaning)
System power variation (reduced or eliminated with periodic recalibration)
Temperature changes (reduced or eliminated with periodic recalibration)
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue E 11/2011
Page 6 of 8
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
相关PDF资料 |
PDF描述 |
|---|---|
| MX6AWT-A1-0000-0009A5 | LED WARM WHITE 350MA 5X5 SMD |
| MX6AWT-A1-0000-0009A3 | LED NEUTRAL WHITE 350MA 5X5 SMD |
| OPB840W11Z | SENS OPTO SLOT 3.18MM TRANS C-MT |
| MX6AWT-A1-0000-0008F7 | LED WARM WHITE 350MA 5X5 SMD |
| OPB815WZ | SENS OPTO SLOT 9.53MM TRANS C-MT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| OPB350W250Z | 制造商:TT Electronics / OPTEK Technology 功能描述:Liquid Level Sensor |
| OPB355 | 制造商:OPTEK 制造商全称:OPTEK 功能描述:Slotted Op tical Switches |
| OPB355_07 | 制造商:OPTEK 制造商全称:OPTEK 功能描述:Slotted Optical Switch |
| OPB355L | 功能描述:光学开关，专业型 Slotted Opt Switch RoHS:否 制造商:ams 感应方式: 安装风格:Through Hole 封装:Tube |
| OPB355N | 功能描述:光学开关，专业型 Slotted Opt Switch RoHS:否 制造商:ams 感应方式: 安装风格:Through Hole 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。