参数资料
| 型号： | P048T048T24AL |
| 厂商： | Vicor Corporation |
| 文件页数： | 10/14页 |
| 文件大小： | 0K |
| 描述： | V.I CHIP PRM REGULATOR 48V 240W |
| 应用说明： | Factorized Power Architecture and V-I Chips |
| 标准包装： | 1 |
| 系列： | V-I Chip™, PRM™ |
| 类型： | 预稳模块 |
| 输出数： | 1 |
| 电压 - 输入（最小）： | 36V |
| 电压 - 输入（最大）： | 75V |
| 输出电压： | 48V |
| 电流 - 输出（最大）： | 5A |
| 电源（瓦） - 制造商系列： | 240W |
| 应用： | 商用 |
| 特点： | 具有远程开/关功能和 UVLO |
| 安装类型： | 通孔 |
| 封装/外壳： | 模块 |
| 尺寸/尺寸： | 1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm） |
| 包装： | 托盘 |
| 工作温度： | -40°C ~ 125°C |
| 效率： | 96% |
| 电源（瓦特）- 最大： | 240W |
| 重量： | 0.033 磅（14.97g） |
| 其它名称： | 1102-1155 P048T048T24AL-ND |
Not Recommended for New Designs
Application Information (continued)
OVP – Overvoltage Protection
The output Overvoltage Protection set point of the P048F048T24AL is
factory preset for 56 V. If this threshold is exceeded the output shuts
down and a restart sequence is initiated, also indicated by PC pulsing.
If the condition that causes OVP is still present, the unit will again shut
V?I Chip Regulator
Adjusting Current Limit
The current limit can be lowered by placing an external resistor
between the I L and SG ports (see Figure 18 for resistor values) . With
the I L port open-circuit, the current limit is preset to be within the
range specified in the output specifications table on Page 4.
down. This cycle will be repeated until the fault condition is removed.
The OVP set point may be set at the factory to meet unique high
voltage requirements.
DC CURRENT LIMIT
PRM Output Power Versus VTM Output Power
As shown in Figure 17, the P048F048T24AL is rated to deliver 5 A
maximum, when it is delivering an output voltage in the range from
26 V to 48 V, and 240 W, maximum, when delivering an output
voltage in the range from 48 V to 55 V. When configuring a PRM for
use with a specific VTM, refer to the appropriate VTM data sheet. The
VTM input power can be calculated by dividing the VTM output power
by the VTM efficiency (available from the VTM data sheet). The input
power required by the VTM should not exceed the output power rating
of the PRM.
100
10
1
0
1
2
3
4
5
6
Desired PRM Output Current Limit (A)
5.1
5.0
4.9
4.8
Figure 18 — Calculated external resistor value for adjusting current limit,
actual value may vary.
4.7
4.6
4.5
4.4
4.3
0
Safe Operating Area
~ ~
20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60
Factorized Bus Voltage (V f )
Input Fuse Recommendations
A fuse should be incorporated at the input to the PRM, in series with
the +In port. A fast acting fuse, NANO2 FUSE 451/453 Series 10 A
125 V, or equivalent, may be required to meet certain safety agency
Conditions of Acceptability. Always ascertain and observe the safety,
regulatory, or other agency specifications that apply to your specific
application.
Product Safety Considerations
If the input of the PRM is connected to SELV or ELV circuits, the output
Figure 17 — P048F048T24AL rating based on Factorized Bus voltage
The Factorized Bus voltage should not exceed an absolute limit of
55 V, including steady state, ripple and transient conditions. Exceeding
this limit may cause the internal OVP set point to be exceeded.
of the PRM can be considered SELV or ELV respectively.
If the input of the PRM is connected to a centralized DC power system
where the working or float voltage is above SELV, but less than or
equal to 75 V, the input and output voltage of the PRM should be
classified as a TNV-2 circuit and spaced 1.3 mm from SELV circuitry or
accessible conductive parts according to the requirements of
UL60950-1, CSA 22.2 60950-1, EN60950-1, and IEC60950-1.
Parallel Considerations
The PR port is used to connect two PRMs in parallel to form a higher
power array. When configuring arrays, PR port interconnection
terminating impedance is 10 k to SG. See note Page 8 and refer to
Application Note AN002. Additionally one PRM should be designated
as the master while all other PRMs are set as slaves by shorting their
SC pin to SG. The PC pins must be directly connected (no diodes) to
assure a uniform start up sequence. Consult Vicor applications
engineering for applications requiring more than two PRMs.
Applications Assistance
Please contact Vicor Applications Engineering for assistance,
1-800-927-9474, or email at apps@vicorpower.com.
vicorpower.com
800-735-6200
V?I Chip Regulator
P048F048T24AL
Rev. 3.9
Page 10 of 14
相关PDF资料 |
PDF描述 |
|---|---|
| 2543000 | FUSEBLOCK 2POLE 10MMX38MM DNRAIL |
| BCM48BH120T120A00 | CONVERTER BUS 12V OUT 120W SMD |
| MP028F036M12AL | REGULATOR PRM 36V OUT 120W SMD |
| B384F120T30 | CONVERTER BUS BCM 12V 300W SMD |
| B048F240T30 | CONVERTER BUS 24V OUT 300W SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P049-010 | 制造商:Tripp Lite 功能描述:TRIPPLITE - Bulk 制造商:Tripp Lite 功能描述:POWER CORD IEC 320/NEMA 5-20P 制造商:Tripp Lite 功能描述:POWER CORD, IEC 320/NEMA 5-20P, BLK, 10F 制造商:Tripp Lite 功能描述:POWER CORD, IEC 320/NEMA 5-20P, BLK, 10FT, 20A; Voltage Rating:125V; Cable Length - Imperial:10ft; Cable Length - Metric:3.05m; Connector Type A:IEC 320 C19; Connector Type B:NEMA 5-20P; Jacket Color:Black; Cable Assembly Type:Power ;RoHS Compliant: Yes |
| P049-01369-03 | 制造商:LG Corporation 功能描述:SPEAKER |
| P-04AF-L22K2 | 制造商:Panasonic Industrial Company 功能描述:BATTERY |
| P04NZ-032 | 制造商:SUMIDA 制造商全称:Sumida Corporation 功能描述:PFC Choke Coil |
| P04P2F-F | 制造商:TE Connectivity 功能描述: |
发布紧急采购，3分钟左右您将得到回复。