- 您现在的位置：买卖IC网 > PDF目录365342 > P6SMBXXXAT3G (ON SEMICONDUCTOR) 600 Watt Peak Power Zener Transient Voltage Suppressors PDF资料下载
参数资料
| 型号： | P6SMBXXXAT3G |
| 厂商： | ON SEMICONDUCTOR |
| 英文描述： | 600 Watt Peak Power Zener Transient Voltage Suppressors |
| 中文描述： | 600瓦峰值功率齐瞬态电压抑制器 |
| 文件页数： | 5/7页 |
| 文件大小： | 77K |
| 代理商： | P6SMBXXXAT3G |
P6SMB6.8AT3 Series
http://onsemi.com
5
APPLICATION NOTES
RESPONSE TIME
In most applications, the transient suppressor device is
placed in parallel with the equipment or component to be
protected. In this situation, there is a time delay associated
with the capacitance of the device and an overshoot
condition associated with the inductance of the device and
the inductance of the connection method. The capacitive
effect is of minor importance in the parallel protection
scheme because it only produces a time delay in the
transition from the operating voltage to the clamp voltage as
shown in Figure 5.
The inductive effects in the device are due to actual
turn-on time (time required for the device to go from zero
current to full current) and lead inductance. This inductive
effect produces an overshoot in the voltage across the
equipment or component being protected as shown in
Figure 6. Minimizing this overshoot is very important in the
application, since the main purpose for adding a transient
suppressor is to clamp voltage spikes. The SMB series have
a very good response time, typically < 1 ns and negligible
inductance. However, external inductive effects could
produce unacceptable overshoot. Proper circuit layout,
minimum lead lengths and placing the suppressor device as
close as possible to the equipment or components to be
protected will minimize this overshoot.
Some input impedance represented by Z
in
is essential to
prevent overstress of the protection device. This impedance
should be as high as possible, without restricting the circuit
operation.
DUTY CYCLE DERATING
The data of Figure 1 applies for non-repetitive conditions
and at a lead temperature of 25
°
C. If the duty cycle increases,
the peak power must be reduced as indicated by the curves
of Figure 7. Average power must be derated as the lead or
ambient temperature rises above 25
°
C. The average power
derating curve normally given on data sheets may be
normalized and used for this purpose.
At first glance the derating curves of Figure 7 appear to be
in error as the 10 ms pulse has a higher derating factor than
the 10 s pulse. However, when the derating factor for a
given pulse of Figure 7 is multiplied by the peak power value
of Figure 1 for the same pulse, the results follow the
expected trend.
相关PDF资料 |
PDF描述 |
|---|---|
| P6SMB120AT3 | 600 Watt Peak Power Zener Transient Voltage Suppressors(峰值功率600W，齐纳TVS) |
| P6SMB200AT3 | 600 Watt Peak Power Zener Transient Voltage Suppressors(峰值功率600W，齐纳TVS) |
| P6SMB11AT3 | 600 Watt Peak Power Zener Transient Voltage Suppressors(峰值功率600W，齐纳TVS) |
| P6SMB12AT3 | 600 Watt Peak Power Zener Transient Voltage Suppressors(峰值功率600W，齐纳TVS) |
| P6SMB13AT3 | 600 Watt Peak Power Zener Transient Voltage Suppressors(峰值功率600W，齐纳TVS) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P6TI58 | 制造商:Panduit Corp 功能描述:CLAMP BEAM 5/16"-1/2" FLANGE 制造商:Panduit Corp 功能描述:BEAM CLAMP FOR 5/16 - 1/2 FLANGE WITH |
| P6T-JP | 制造商:Schneider Electric 功能描述:APC SURGEARREST ESSENTIAL, LIGHTNING GUARD EXTENSION + TELEP - Bulk |
| P6TM | 功能描述:电源排插 6 Out /Phone Protect 120V Metal RoHS:否 制造商:Wiremold 出口数量: 浪涌能量额定值: 数据线路保护:N 电线长度:15 ft 安装风格: 输出电压:120 V 电流额定值:15 A |
| P6TM10 | 功能描述:电源排插 6 Out /Phone Protect 10Ft Cord,120V Metal RoHS:否 制造商:Wiremold 出口数量: 浪涌能量额定值: 数据线路保护:N 电线长度:15 ft 安装风格: 输出电压:120 V 电流额定值:15 A |
| P6V | 制造商:American Power Conversion Corp 功能描述:Six Outlet Wall Tap Surge Protector with Coax Protection |
发布紧急采购，3分钟左右您将得到回复。