- 您现在的位置：买卖IC网 > PDF目录367742 > P80CE558 (NXP Semiconductors N.V.) Single-chip 8-bit microcontroller(8位单片微控制器) PDF资料下载
参数资料
| 型号： | P80CE558 |
| 厂商： | NXP Semiconductors N.V. |
| 英文描述： | Single-chip 8-bit microcontroller(8位单片微控制器) |
| 中文描述： | 单芯片8位微控制器（8位单片微控制器） |
| 文件页数： | 7/72页 |
| 文件大小： | 721K |
| 代理商： | P80CE558 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
Philips Semiconductors
Preliminary specification
P83CE558/P80CE558/P89CE558
Single-chip 8-bit microcontroller
1996 Aug 06
7
PIN DESCRIPTION
(Continued)
SYMBOL
PIN
DESCRIPTION
P3.0 – P3.7
41 – 48
8-bit quasi-bidirectional I/O port
Port pin
P3.0
P3.1
P3.2
P3.3
P3.4
P3.5
P3.6
P3.7
Alternative function
RXD
TXD
INT0
INT1
T0
T1
WR
RD
:
:
:
:
:
:
:
:
Serial input port
Serial output port
External interrupt
External interrupt
Timer 0 external input
Timer 1 external input
External data memory write strobe
External data memory read strobe
N.C.
49 – 50
Not connected pins.
XTAL2
51
Crystal pin 2
: output of the inverting amplifier that forms the oscillator. Left open-circuit when an external
oscillator clock is used.
XTAL1
52
Crystal pin 1
: input to the inverting amplifier that forms the oscillator, and input to the internal clock
generator. Receives the external oscillator clock signal when an external oscillator is used. Must be
connected to logic HIGH if the PLL oscillator is selected (SELXTAL1 = LOW).
P2.0 – P2.7
55 – 62
Port2:
8-bit quasi-bidirectional I/O port with internal pull-ups.During access to external memories
(RAM/ROM) that use 16-bit addresses (MOVX@DPTR) Port 2 emits the high order address byte. The
alternative function of P2.7 for the P89CE558 is the output enable signal for verify/read modes (active low).
Port 2 can sink/source one TTL (=4 LSTTL) input. It can drive CMOS inputs without external pull-ups.
PSEN
63
Program Store Enable output:
read strobe to the external program memory via Port 0 and 2. Is activated
twice each machine cycle during fetches from external program memory. When executing out of external
program memory two activations of PSEN are skipped during each access to external data memory. PSEN
is not activated (remains HIGH) during no fetches from external program memory. PSEN can sink/source 8
LSTTL inputs. It can drive CMOS inputs without external pull-ups.
ALE/WE
64
Address Latch Enable output
: latches the low byte of the address during access of external memory in
normal operation. It is activated every six oscillator periods except during an external data memory access.
ALE/WE can sink/-source 8 LSTTL inputs. It can drive CMOS inputs without an external pull-up. The
alternative function for the P89CE558 is the programming pulse input WE.
To prohibit the toggling of ALE pin (RFI noise reduction) the bit RFI in the PCON Register (PCON.5) must be
set by software. This bit is cleared on RESET and can be set and cleared by software. When set, ALE pin
will be pulled down internally, switching an external address latch to a quiet state. The MOVX instruction will
still toggle ALE if external memory is accessed.
ALE will retain its normal high value during Idle Mode and a low value during Power-down Mode while in the
“RFI” mode. Additionally during internal access (EA = 1) ALE will toggle normally when the address exceeds
the internal program memory size. During external access (EA = 0) ALE will always toggle normally, whether
the flag “RFI” is set or not.
EA
65
External Access Input:
If, during RESET, EA is held at a TTL level HIGH the CPU executes out of the
internal program memory, provided the program counter is less than 32768. If, during RESET, EA is held at a
TTL level LOW the CPU executes out of external program memory via Port 0 and Port 2. EA is not allowed
to float. EA is latched during RESET and don’t care after RESET.
P0.7–P0.0
68 –75
Port 0:
8-bit open drain bidirectional I/O port. It is also the multiplexed low-order address and data bus during
accesses to external memory (during theses accesses internal pull-ups are activated). Port 0 can sink/source
8 LSTTL inputs.
XTAL3
78
Crystal pin
, output of the inverting amplifier that forms the 32 kHz oscillator
XTAL4
79
Crystal pin
, input to the inverting amplifier that forms the 32 kHz oscillator. XTAL3 and XTAL4 are pulled
LOW if the PLL oscillator is not selected (SELXTAL1 = HIGH) or if Reset is active.
SELXTAL1
80
Must be connected to logic HIGH level to select the HF oscillator, using the XTAL1/XTAL2 crystal. If pulled low
the PLL is selected for clocking of the controller, using the XTAL3/ XTAL4 crystal.
NOTE:
1. To avoid a ‘latch-up’ effect at Power-on, the voltage at any pin at any time must not be higher or lower than V
DD
+ 0.5 V or V
SS
– 0.5 V
respectively.
相关PDF资料 |
PDF描述 |
|---|---|
| P80CE558EBB | Single-chip 8-bit microcontroller |
| P80CE558EFB | Single-chip 8-bit microcontroller |
| P89LPC901 | 8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM |
| P89LPC901FD | 8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM |
| P89LPC901FN | 8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P80CE558EBB | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Single-chip 8-bit microcontroller |
| P80CE558EFB | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Single-chip 8-bit microcontroller |
| P80CE559 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Single-chip 8-bit microcontroller |
| P80CE559EBB | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Single-chip 8-bit microcontroller |
| P80CE559EFB | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Single-chip 8-bit microcontroller |
发布紧急采购，3分钟左右您将得到回复。