- 您现在的位置：买卖IC网 > PDF目录367726 > P83C366BDR (NXP SEMICONDUCTORS) Microcontrollers for PAL/SECAM TV with OSD and VST(带 OSD和 VST的在PAL/SECAM TV中应用的微控制器) PDF资料下载
参数资料
| 型号： | P83C366BDR |
| 厂商： | NXP SEMICONDUCTORS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | Microcontrollers for PAL/SECAM TV with OSD and VST(带 OSD和 VST的在PAL/SECAM TV中应用的微控制器) |
| 中文描述： | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PDIP42 |
| 封装： | 0.600 INCH, PLASTIC, SDIP-42 |
| 文件页数： | 87/92页 |
| 文件大小： | 382K |
| 代理商： | P83C366BDR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页当前第87页第88页第89页第90页第91页第92页
1999 Mar 10
87
Philips Semiconductors
Product specification
Microcontrollers for PAL/SECAM TV
with OSD and VST
P8xCx66 family
24 SOLDERING
24.1
Introduction
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mount components are mixed on
one printed-circuit board. However, wave soldering is not
always suitable for surface mount ICs, or for printed-circuit
boards with high population densities. In these situations
reflow soldering is often used.
24.2
Through-hole mount packages
24.2.1
S
OLDERING BY DIPPING OR BY SOLDER WAVE
The maximum permissible temperature of the solder is
260
°
C; solder at this temperature must not be in contact
with the joints for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (T
stg(max)
). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
24.2.2
M
ANUAL SOLDERING
Apply the soldering iron (24 V or less) to the lead(s) of the
package, either below the seating plane or not more than
2 mm above it. If the temperature of the soldering iron bit
is less than 300
°
C it may remain in contact for up to
10 seconds. If the bit temperature is between
300 and 400
°
C, contact may be up to 5 seconds.
24.3
Surface mount packages
24.3.1
R
EFLOW SOLDERING
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
infrared/convection heating in a conveyor type oven.
Throughput times (preheating, soldering and cooling) vary
between 100 and 200 seconds depending on heating
method.
Typical reflow peak temperatures range from
215 to 250
°
C. The top-surface temperature of the
packages should preferable be kept below 230
°
C.
24.3.2
W
AVE SOLDERING
Conventional single wave soldering is not recommended
for surface mount devices (SMDs) or printed-circuit boards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is
preferred
to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the transport direction of the
printed-circuit board.
The footprint must incorporate solder thieves at the
downstream end.
For packages with leads on four sides, the footprint must
be placed at a 45
°
angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical dwell time is 4 seconds at 250
°
C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
24.3.3
M
ANUAL SOLDERING
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300
°
C.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320
°
C.
相关PDF资料 |
PDF描述 |
|---|---|
| P83C366CBP | Microcontrollers for PAL/SECAM TV with OSD and VST(带 OSD和 VST的在PAL/SECAM TV中应用的微控制器) |
| P87C766BDR | Microcontrollers for PAL/SECAM TV with OSD and VST |
| P87C766CBA | Microcontrollers for PAL/SECAM TV with OSD and VST |
| P87C766CBP | Microcontrollers for PAL/SECAM TV with OSD and VST |
| P87C766 | Microcontrollers for PAL/SECAM TV with OSD and VST |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P83C366CBP | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Microcontrollers for PAL/SECAM TV with OSD and VST |
| P83C370 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Microcontrollers for NTSC TVs with On-Screen Display OSD and Closed Caption CC |
| P83C370AAR | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Microcontrollers for NTSC TVs with On-Screen Display OSD and Closed Caption CC |
| P83C380 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Microcontrollers for monitors with DDC interface, auto-sync detection and sync proc. |
| P83C434 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit microcontrollers with LCD-driver |
发布紧急采购，3分钟左右您将得到回复。