参数资料
型号: P83C566
厂商: NXP Semiconductors N.V.
英文描述: Microcontrollers for PAL/SECAM TV with OSD and VST
中文描述: 微控制器对于PAL / SECAM电视的OSD和伟仕
文件页数: 13/92页
文件大小: 382K
代理商: P83C566
1999 Mar 10
13
Philips Semiconductors
Product specification
Microcontrollers for PAL/SECAM TV
with OSD and VST
P8xCx66 family
8
TIMERS AND EVENT COUNTERS
The P8xCx66 contains two 16-bit timers/counters: Timer 0
and Timer 1 and also an 8-bit Watchdog timer.
8.1
16-bit timer/counters (T0 and T1)
Timer 0 and Timer 1 perform the following functions:
Measure time intervals and pulse durations
Count events
Generate interrupt requests.
Timer 0 and Timer 1 can be independently programmed to
operate in one of four modes.
Mode 0 8-bit timer or counter with divide-by-32 prescaler.
Mode 1 16-bit time-interval or event counter.
Mode 2 8-bit time-interval or event counter with automatic
reload upon overflow.
Mode 3 Timer 0 establishes TL0 and TL1 as two
separate counters.
In the ‘timer’ function, the register is incremented every
machine cycle. Since a machine cycle consists of
12 oscillator periods, the count rate is
1
12
f
osc
.
In the ‘counter’ function, the register is incremented in
response to a HIGH-to-LOW transition. Since it takes
2 machine cycles (24 oscillator periods) to recognize a
HIGH-to-LOW transition, the maximum count rate is
1
24
f
osc
. To ensure that a given level is sampled, it should
be held for at least one complete machine cycle.
8.2
Watchdog timer (T3)
In addition to the standard timers, a Watchdog timer is
implemented on-chip. The Watchdog timer generates a
hardware reset upon overflow. In this way a
microcontroller system can recover from erroneous
processor states caused by electrical noise, RFI or
unexpected ROM code behaviour.
The Watchdog timer consists of an 8-bit timer with an
11-bit prescaler as shown in Fig.8. The prescaler input
frequency is
1
12
f
osc
. The 8-bit timer is incremented every
‘t’ seconds where ‘t’ is calculated as shown below:
The 8-bit timer is an up-counter so a value 00H gives the
maximum timer interval (510 ms at 12 MHz, 1536 ms at
4 MHz), and a value of FFH gives the minimum timer
interval (2 ms at 12 MHz, 6 ms at 4 MHz). When the 8-bit
timer produces an overflow a short internal reset pulse is
generated which will reset the P8xCx66.
The timer has no disable function. Consequently, all
applications must reload the timer within the previously
loaded timer interval otherwise a reset will occur. The timer
is not stopped in the Idle mode. The interrupt routine for
the Idle mode should also service the Watchdog timer.
The Watchdog timer is controlled by the WLE bit in the
Power Control Register (see Section 9.6). The WLE bit
must be set by the Watchdog timer service routine before
the timer interval can be loaded into T3. A load of T3
automatically clears the WLE bit.
A system reset clears the Watchdog timer and the
prescaler.
8.2.1
W
ATCHDOG TIMER
R
EGISTER
(WDT)
Table 3
Watchdog timer Register (SFR address FFH)
7
6
5
4
3
2
1
0
T37
T36
T35
T34
T33
T32
T31
T30
t
12
2048
×
f
osc
-1
×
=
相关PDF资料
PDF描述
P83C566BDR Microcontrollers for PAL/SECAM TV with OSD and VST
P83C366BDR Microcontrollers for PAL/SECAM TV with OSD and VST(带 OSD和 VST的在PAL/SECAM TV中应用的微控制器)
P83C366CBP Microcontrollers for PAL/SECAM TV with OSD and VST(带 OSD和 VST的在PAL/SECAM TV中应用的微控制器)
P87C766BDR Microcontrollers for PAL/SECAM TV with OSD and VST
P87C766CBA Microcontrollers for PAL/SECAM TV with OSD and VST
相关代理商/技术参数
参数描述
P83C566BDA 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Microcontrollers for PAL/SECAM TV with OSD and VST
P83C566BDR 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Microcontrollers for PAL/SECAM TV with OSD and VST
P83C570 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Microcontrollers for NTSC TVs with On-Screen Display OSD and Closed Caption CC
P83C570AAR 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Microcontrollers for NTSC TVs with On-Screen Display OSD and Closed Caption CC
P83C575EBA 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller