- 您现在的位置：买卖IC网 > PDF目录367726 > P83C766BDA (NXP SEMICONDUCTORS) Microcontrollers for PAL/SECAM TV with OSD and VST(带 OSD和 VST的在PAL/SECAM TV中应用的微控制器) PDF资料下载
参数资料
| 型号： | P83C766BDA |
| 厂商： | NXP SEMICONDUCTORS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | Microcontrollers for PAL/SECAM TV with OSD and VST(带 OSD和 VST的在PAL/SECAM TV中应用的微控制器) |
| 中文描述： | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQCC68 |
| 封装： | PLASTIC, MO-047AC, SOT-188-2, LCC-68 |
| 文件页数： | 26/80页 |
| 文件大小： | 266K |
| 代理商： | P83C766BDA |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
1999 Jun 11
26
Philips Semiconductors
Product specification
Microcontrollers for NTSC TVs with On-Screen
Display (OSD) and Closed Caption (CC)
P8xCx70 family
12 OSCILLATOR CIRCUITRY
The on-chip oscillator circuitry of the P8xCx70 is a
single-stage inverting amplifier biased by an internal
feedback resistor. For operation as a standard quartz
oscillator or when using an external ceramic resonator,
external components are needed and should be
connected as shown in Fig.8.
In the Power-down mode the oscillator is stopped and both
XI and XO are pulled HIGH. The inverting amplifier and
feedback resistor are both switched off to ensure no
current will flow regardless of the voltages at XI and XO.
To drive the device with an external clock source, apply the
external clock signal to XI, and leave XO to float. There is
no requirement on the duty cycle of the external clock,
because the external clock is divided-by-two using a
flip-flop before feeding the internal clocking circuitry.
The operating frequency of crystal oscillator is fixed at
12 MHz.
13 RESET
There are three ways to invoke a reset and initialize the
P8xCx70:
Via the external RESET pin
Via the on-chip Power-on reset circuitry
Via a Watchdog Timer overflow.
Fig.8 Oscillator configuration.
For quartz crystal or ceramic resonator.
handbook, halfpage
MBE311
XI
XO
The reset mechanism is illustrated in Fig.9. Each reset
source will cause the internal reset signal POC to become
active. The CPU responds by executing an internal reset
putting the internal registers into a defined state as
detailed in Table 34.
13.1
External reset
The reset pin RESET is connected to a Schmitt trigger for
noise reduction (see Fig.9). A reset is accomplished by
holding the RESET pin HIGH for at least 2 machine cycles
(24 system clocks), while the oscillator is running.
If the RESET pin is connected to V
DD
via a capacitor as
shown in Fig.9, an automatic reset can be obtained by
switching on V
DD
, The V
DD
rise time must not exceed
10 ms and the capacitor should be at least 10
μ
F.
The decrease of the RESET pin voltage depends on the
capacitor and the internal resistor R
RESET
. The voltage
must remain above the lower threshold level for a
minimum period determined by the oscillator start-up time
plus 2 machine cycles. For the P8xCx70 an external
capacitor value of 10
μ
F is needed.
13.2
Power-on reset
An on-chip Power-on reset circuit detects supply voltage
variations and generates a Power-on reset pulse
accordingly; see Fig.10.
In the case of supply voltage ramp-up, the power-on reset
signal follows the ramp-up of the supply voltage. When the
trip level (V
t
) is reached, the power-on reset signal will be
maintained for a time period (T
p
) before reverting back to
its LOW state.
In the case of supply voltage drop, after the trip level (V
t
) is
reached, the power-on reset signal will respond within T
r
.
The internal reset will remain active until T
p
after the V
t
has
been exceeded.
The time interval (T
p
) is used to guarantee a complete
power-on reset pulse so that this signal can trigger the
internal reset signal. However, to ensure the oscillator is
stable before the controller starts, the clock is gated away
from the CPU for a further 2048 oscillator cycles.
13.3
Watchdog Timer overflow
The length of the output pulse from T3 is 3 machine cycles.
A pulse of such short duration is necessary in order to
recover from a processor or system fault as fast as
possible.
相关PDF资料 |
PDF描述 |
|---|---|
| P83C770 | Microcontrollers for NTSC TVs with On-Screen Display (OSD) and Closed Caption (CC)(在NTSC TV中应用的具有屏幕显示和字幕关闭特点的微控制器) |
| P83C366BDA | Microcontrollers for PAL/SECAM TV with OSD and VST(带 OSD和 VST的在PAL/SECAM TV中应用的微控制器) |
| P83C566BDA | Microcontrollers for PAL/SECAM TV with OSD and VST(带 OSD和 VST的在PAL/SECAM TV中应用的微控制器) |
| P87C770AAR | Microcontrollers for NTSC TVs with On-Screen Display OSD and Closed Caption CC |
| P83C270 | Microcontrollers for NTSC TVs with On-Screen Display (OSD) and Closed Caption (CC)(在NTSC TV中应用的具有屏幕显示和字幕关闭特点的微控制器) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P83C766BDP | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Microcontrollers for PAL/SECAM TV with OSD and VST |
| P83C770 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Microcontrollers for NTSC TVs with On-Screen Display OSD and Closed Caption CC |
| P83C770AAR | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Microcontrollers for NTSC TVs with On-Screen Display OSD and Closed Caption CC |
| P83C834 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit microcontrollers with LCD-driver |
| P83C834CFP | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit microcontrollers with LCD-driver |
发布紧急采购，3分钟左右您将得到回复。