- 您现在的位置：买卖IC网 > PDF目录367736 > P87C51FC-JN (NXP SEMICONDUCTORS) 80C51 8-bit microcontroller family 8K.64K/256.1K OTP/ROM/ROMless, low voltage 2.7V.5.5V, low power, high speed 33 MHz PDF资料下载
参数资料
| 型号： | P87C51FC-JN |
| 厂商： | NXP SEMICONDUCTORS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 80C51 8-bit microcontroller family 8K.64K/256.1K OTP/ROM/ROMless, low voltage 2.7V.5.5V, low power, high speed 33 MHz |
| 中文描述： | 8-BIT, OTPROM, 33 MHz, MICROCONTROLLER, PDIP40 |
| 封装： | 0.600 INCH, PLASTIC, MO-015, SOT-129-1, DIP-40 |
| 文件页数： | 8/34页 |
| 文件大小： | 394K |
| 代理商： | P87C51FC-JN |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
2001 Apr 06
8
Philips Semiconductors
Preliminary specification
P87C51MB2/P87C51MC2
80C51 8-bit microcontroller family with extended memory
64KB/96KB OTP with 2KB/3KB RAM
P4.0 - P4.1
12,34
I/O
Port 4:
Port 4 is an 8-bit bidirectional I/O port with internal pull-ups on all pin. Port 4 pins
that have 1s written to them are pulled high by the internal pull-ups and can be used as
inputs. As inputs, port 4 pins that are externally pulled low will source current because of
the internal pull-ups. (Note: When SFR bit SPEN (SPCTL.6) is ’1’, the pull-ups at these port
pins are disabled.)
P4.0
RXD1
Serial input port 1. (Note: This pin is a no connect pin on some
derivatives.) (with pull-up on pin)
MISO
SPI Master In/Slave Out (Selected when SFR bit SPEN (SPCTL.6)
is ’1’, in which case the pull-up for this pin is disabled)
P4.1
TXD1
Serial output port 1. (Note: This pin is a no connect pin on some
derivatives.) (with pull-up on pin)
SS
SPI Slave Select (Selected when SFR bit SPEN (SPCTL.6) is ’1’,
in which case the pull-up for this pin is disabled)
Reset:
A high on this pin for two machine cycles while the oscillator is running, resets the
device. An internal diffused resistor to V
SS
permits a power-on reset using only an external
capacitor to V
DD.
Address Latch Enable:
Output pulse for latching the low byte of the address during an
access to external memory. In normal operation, ALE is emitted at a constant rate of 1/6
the oscillator frequency, and can be used for external timing or clocking. Note that one ALE
pulse is skipped during each access to external data memory. If SFR bit AO (AUXR.0) is
’0’, ALE is emitted at the constant rate as indicated above. With this bit set to ’1’, ALE will
be active only during a MOVX instruction.
Program Store Enable:
The read strobe to external program memory. When executing
code from the external program memory, PSEN is activated twice each machine cycle,
except that two PSEN activations are skipped during each access to external data
memory. PSEN is not activated during fetches from internal program memory.
External Access Enable/Programming Supply Voltage:
EA must be externally held low
to enable the device to fetch code from external program memory locations. If EA is held
high, the device executes from internal program memory. The value on the EA pin is
latched when RST is released and any subsequent changes have no effect.
Crystal 1:
Input to the inverting oscillator amplifier and input to the internal clock generator
circuits.
Crystal 2:
Output from the inverting oscillator amplifier.
Ground:
0V reference.
12
I
I/O
34
O
I
RST
10
I
ALE
33
O
PSEN
32
O
EA/Vpp
35
I
XTAL1
21
I
XTAL2
V
SS
V
DD
20
22
O
I
44
I
Power Supply:
This is the power supply voltage for normal operation as well as Idle and
Power Down modes.
No Connect/Ground:
This pin is a no connect pin on some derivatives, but is internally
connected to V
SS
on the P87C51Mx2. If connected externally, this pin must only be
connected to the same V
SS
as at pin 22. (Note: Connecting the second pair of V
SS
and V
DD
pins is not required. However, they may be connected in addition to the primary V
SS
and
V
DD
pins to improve power distribution, reduce noise in output signals, and improve
system-level EMI characteristics.)
No Connect/Power Supply:
This pin is a no connect pin on some derivatives, but is
internally connected to V
DD
on the P87C51Mx2. If connected externally, this pin must only
be connected to the same V
DD
as at pin 44. (Note: Connecting the second pair of V
SS
and
V
DD
pins is not required. However, they may be connected in addition to the primary V
SS
and V
DD
pins to improve power distribution, reduce noise in output signals, and improve
system-level EMI characteristics.)
(NC/V
SS
)
1
I
(NC/V
DD
)
23
I
MNEMONIC
PIN NO.
TYPE NAME AND FUNCTION
相关PDF资料 |
PDF描述 |
|---|---|
| P87C528EFPN | CMOS single-chip 8-bit microcontroller |
| P80C528IBA | 8-bit microcontrollers |
| P80C528EFA | 8-bit microcontrollers |
| P83C528EFA | 8-bit microcontrollers |
| P80C528EFB | 8-bit microcontrollers |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P87C51FC–JN | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:80C51 8-bit microcontroller family 8K-64K/256-1K OTP/ROM/ROMless. low voltage 2.7V-5.5V). low power. high speed (33 MHz) |
| P87C51GA | 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller |
| P87C51GA-1 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller |
| P87C51GA-2 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller |
| P87C51MB2 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:80C51 8-bit microcontroller family with extended memory |
发布紧急采购，3分钟左右您将得到回复。