参数资料
| 型号： | P87C51RB2BN,112 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 51/67页 |
| 文件大小： | 0K |
| 描述： | IC 80C51 MCU 16K OTP 40-DIP |
| 产品培训模块： | Migrating from 8/16-Bit MCUs to 32-Bit ARMs |
| 标准包装： | 9 |
| 系列： | 87C |
| 核心处理器： | 8051 |
| 芯体尺寸： | 8-位 |
| 速度： | 33MHz |
| 连通性： | EBI/EMI，UART/USART |
| 外围设备： | POR，PWM，WDT |
| 输入/输出数： | 32 |
| 程序存储器容量： | 16KB（16K x 8） |
| 程序存储器类型： | OTP |
| RAM 容量： | 512 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 振荡器型： | 内部 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 40-DIP（0.600"，15.24mm） |
| 包装： | 管件 |
| 产品目录页面： | 705 (CN2011-ZH PDF) |
| 其它名称： | 568-3200-5 935271895112 P87C51RB2BN |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页当前第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页
Philips Semiconductors
Product data
P87C51RA2/RB2/RC2/RD2
80C51 8-bit microcontroller family 8KB/16KB/32KB/64KB OTP
with 512B/1KB RAM, low voltage (2.7 to 5.5 V), low power, high
speed (30/33 MHz)
2003 Jan 24
55
EPROM CHARACTERISTICS
All these devices can be programmed by using a modified Improved
Quick-Pulse Programming
algorithm. It differs from older methods
in the value used for VPP (programming supply voltage) and in the
width and number of the ALE/PROG pulses.
The family contains two signature bytes that can be read and used
by an EPROM programming system to identify the device. The
signature bytes identify the device as being manufactured by
Philips.
Table 8 shows the logic levels for reading the signature byte, and for
programming the program memory, the encryption table, and the
security bits. The circuit configuration and waveforms for quick-pulse
programming are shown in Figures 47 and 48. Figure 49 shows the
circuit configuration for normal program memory verification.
Quick-Pulse Programming
The setup for microcontroller quick-pulse programming is shown in
Figure 47. Note that the device is running with a 4 to 6MHz
oscillator. The reason the oscillator needs to be running is that the
device is executing internal address and program data transfers.
The address of the EPROM location to be programmed is applied to
ports 1 and 2, as shown in Figure 47. The code byte to be
programmed into that location is applied to port 0. RST, PSEN and
pins of ports 2 and 3 specified in Table 8 are held at the ‘Program
Code Data’ levels indicated in Table 8. The ALE/PROG is pulsed
low 5 times as shown in Figure 48.
To program the encryption table, repeat the 5 pulse programming
sequence for addresses 0 through 1FH, using the ‘Pgm Encryption
Table’ levels. Do not forget that after the encryption table is
programmed, verification cycles will produce only encrypted data.
To program the security bits, repeat the 5 pulse programming
sequence using the ‘Pgm Security Bit’ levels. After one security bit is
programmed, further programming of the code memory and
encryption table is disabled. However, the other security bits can still
be programmed.
Note that the EA/VPP pin must not be allowed to go above the
maximum specified VPP level for any amount of time. Even a narrow
glitch above that voltage can cause permanent damage to the
device. The VPP source should be well regulated and free of glitches
and overshoot.
Program Verification
If security bits 2 and 3 have not been programmed, the on-chip
program memory can be read out for program verification. The
address of the program memory locations to be read is applied to
ports 1 and 2 as shown in Figure 49. The other pins are held at the
‘Verify Code Data’ levels indicated in Table 8. The contents of the
address location will be emitted on port 0. External pull-ups are
required on port 0 for this operation.
If the 64 byte encryption table has been programmed, the data
presented at port 0 will be the exclusive NOR of the program byte
with one of the encryption bytes. The user will have to know the
encryption table contents in order to correctly decode the verification
data. The encryption table itself cannot be read out.
Reading the Signature Bytes
The signature bytes are read by the same procedure as a normal
verification of locations 030H and 031H, except that P3.6 and P3.7
need to be pulled to a logic low. The values are:
(030H) = 15H indicates manufactured by Philips
(031H) = CAH indicates 87C51RA2
CBH indicates 87C51RB2
CCH indicates 87C51RC2
CDH indicates 87C51RD2
(060H) = NA
Program/Verify Algorithms
Any algorithm in agreement with the conditions listed in Table 8, and
which satisfies the timing specifications, is suitable.
Security Bits
With none of the security bits programmed the code in the program
memory can be verified. If the encryption table is programmed, the
code will be encrypted when verified. When only security bit 1 (see
Table 9) is programmed, MOVC instructions executed from external
program memory are disabled from fetching code bytes from the
internal memory, EA is latched on Reset and all further programming
of the EPROM is disabled. When security bits 1 and 2 are
programmed, in addition to the above, verify mode is disabled.
When all three security bits are programmed, all of the conditions
above apply and all external program memory execution is disabled.
Encryption Array
64 bytes of encryption array are initially unprogrammed (all 1s).
Trademark phrase of Intel Corporation.
相关PDF资料 |
PDF描述 |
|---|---|
| P87C52SFAA,512 | IC 80C51 MCU 8K OTP 44-PLCC |
| P87C54X2BN,112 | IC 80C51 MCU 256 RAM 40DIP |
| P87LPC760BDH,112 | IC 80C51 MCU 1K OTP 14-TSSOP |
| P87LPC762FN,112 | IC 80C51 MCU 2K OTP 20-DIP |
| P87LPC764FD,512 | IC 80C51 MCU 4K OTP 20-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P87C51RB2FA | 制造商:NXP Semiconductors 功能描述:MCU 8-bit P87 80C51 CISC 16KB EPROM 3.3V/5V 44-Pin PLCC Tube |
| P87C51RB2FA,512 | 功能描述:8位微控制器 -MCU 16K/512 OTP 12 CLK IND PLCC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| P87C51RB2FN | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:80C51 8-bit microcontroller family |
| P87C51RB4A | 制造商:NXP Semiconductors 功能描述:MCU 8-bit 8XC51 80C51 CISC 16KB EPROM 3.3V/5V 44-Pin PLCC |
| P87C51RC+4A | 制造商:NXP Semiconductors 功能描述:IC 8BIT MCU OTP 32K 87C51 PLCC44 |
发布紧急采购，3分钟左右您将得到回复。