- 您现在的位置：买卖IC网 > PDF目录367728 > P87C576EHPN (NXP SEMICONDUCTORS) 80C51 8-bit microcontroller family 8K/256 OTP/ROM, 6 channel 10-bit A/D, 4 comparators, failure detect circuitry, watchdog timer PDF资料下载
参数资料
| 型号： | P87C576EHPN |
| 厂商： | NXP SEMICONDUCTORS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 80C51 8-bit microcontroller family 8K/256 OTP/ROM, 6 channel 10-bit A/D, 4 comparators, failure detect circuitry, watchdog timer |
| 中文描述： | 8-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PDIP40 |
| 封装： | 0.600 INCH, PLASTIC, MO-015AJ, SOT-129-1, DIP-40 |
| 文件页数： | 23/46页 |
| 文件大小： | 447K |
| 代理商： | P87C576EHPN |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
Philips Semiconductors
Product specification
83C576/87C576
80C51 8-bit microcontroller family
8K/256 OTP/ROM, 6 channel 10-bit A/D, 4 comparators,
failure detect circuitry, watchdog timer
1998 Jun 04
23
SM0
SM1
SM2
REN
TB8
RB8
TI
RI
SCON
(98H)
D0
D1
D2
D3
D4
D5
D6
D7
D8
1
1
1
0
COMPARATOR
1
1
X
RECEIVED ADDRESS D0 TO D7
PROGRAMMED ADDRESS
IN UART MODE 2 OR MODE 3 AND SM2 = 1:
INTERRUPT IF REN=1, RB8=1 AND “RECEIVED ADDRESS” = “PROGRAMMED ADDRESS”
– WHEN OWN ADDRESS RECEIVED, CLEAR SM2 TO RECEIVE DATA BYTES
– WHEN ALL DATA BYTES HAVE BEEN RECEIVED: SET SM2 TO WAIT FOR NEXT ADDRESS.
SU00045
Figure 21.
UART Multiprocessor Communication, Automatic Address Recognition
CMP Register Bit Definitions
CMP.7
enable comparator 3
CMP.6
enable comparator 2
CMP.5
enable comparator 1,
CMP.4
enable comparator 0
CMP.3
comparator 3 output (read only)
CMP.2
comparator 2 output (read only)
CMP.1
comparator 1 output (read only)
CMP.0
comparator 0 output (read only)
All comparators are disabled automatically in power down mode. In
idle mode unused comparators should be disabled by software to
save power. A comparator can generate an interrupt that will
terminate idle mode when used to drive a PCA capture input.
The CMPE register contains bits to enable each comparator to drive
external output pins or internal PCA capture inputs. When the
comparator is configured for external output, the user must also
configure the output port in one of its output modes. The comparator
output is wire-ORed with the corresponding port SFR bit, so the
SFR bit must also be set by software to enable the output.
CMPE Register Bit Definitions
CMPE.7 enables comparator 3 to drive CEX3
CMPE.6 enables comparator 2 to drive CEX2
CMPE.5 enables comparator 1 to drive CEX1
CMPE.4 enables comparator 0 to drive CEX0
CMPE.3 enables comparator 3 output on P2.3
CMPE.2 enables comparator 2 output on P2.2
CMPE.1 enables comparator 1 output on P2.1
CMPE.0 enables comparator 0 output on P2.0
When 1s are written to CMPE bits 7-4, the comparator outputs will
drive the corresponding capture input. When 1s are written to CMPE
bits 3-0 the comparator output will also drive the corresponding
port 2 pin. If the comparator’s enabled to drive the capture input but
not the port pin, then the port pin can be used for general purpose
I/O. When a comparator output is enabled, the user will need to
configure the port for one of its output modes.
There are two special function registers associated with the
comparators. They are CMP which contains the comparator enables
and a bit that can be read by software to determine the state of each
comparator’s output, and CMPE which controls whether the output
from each comparator drives the associated output pin or a capture
input associated with one of the PCA modules.
The CMP registers bits 0–3 can be read by software to determine
the state of the output of each comparator. To do this the associated
comparator must be enabled but the output in port 2 can be
disabled. This allows easy polling of the comparator output value
without the need to use up a port pin.
The CMPE register allows the comparator to drive the associated
PCA module capture input, so that on compare a capture can be
generated in the PCA. Bits 0–3 of this register enable the
comparator output to drive the associated port 2 output circuitry.
Used as a comparator output, the output mode for this port must be
configured for output by the user and the port output SFR bit latch
must be set. If the comparator is not enabled to drive the port 2
circuitry, the associated port 2 pin can be used for other I/O. This
includes when a comparator is enabled to drive the capture input to
a PCA module.
Reduced EMI Mode
There are two bits in the AUXR register that can be set to reduce
the internal clock drive and disable the ALE output. AO (AUXR.0)
when set turns off the ALE output. LO (AUXR.1) when set reduces
the drive of the internal clock circuitry. Both bits are cleared on
Reset. With LO set the 8XC576 will still operate at 12MHz, and will
have reduced EMI in the range above 100MHz.
8XC576 Reduced EMI Mode
AUXR (0X8E)
––
––
––
––
RST
TXI
LO
AO
AO:
LO:
Turns off ALE output.
Reduces drive of internal clock circuitry. 8XC576 spec’d to
12MHz when LO set.
Inverts TxD when set.
RST: Software reset.
TXI:
相关PDF资料 |
PDF描述 |
|---|---|
| P83C576EBBB | 80C51 8-bit microcontroller family 8K/256 OTP/ROM, 6 channel 10-bit A/D, 4 comparators, failure detect circuitry, watchdog timer |
| P87C576EBBB | 80C51 8-bit microcontroller family 8K/256 OTP/ROM, 6 channel 10-bit A/D, 4 comparators, failure detect circuitry, watchdog timer |
| P87C576EBAA | 80C51 8-bit microcontroller family 8K/256 OTP/ROM, 6 channel 10-bit A/D, 4 comparators, failure detect circuitry, watchdog timer |
| P83C576EBPN | 80C51 8-bit microcontroller family 8K/256 OTP/ROM, 6 channel 10-bit A/D, 4 comparators, failure detect circuitry, watchdog timer |
| P87C576EBPN | 80C51 8-bit microcontroller family 8K/256 OTP/ROM, 6 channel 10-bit A/D, 4 comparators, failure detect circuitry, watchdog timer |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P87C581SF76 | 功能描述:IC MCU 8BIT 32K 16MHZ OTP 40-DIP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:87C 其它有关文件:STM32F101T8 View All Specifications 特色产品:STM32 32-bit Cortex MCUs 标准包装:490 系列:STM32 F1 核心处理器:ARM? Cortex?-M3 芯体尺寸:32-位 速度:36MHz 连通性:I²C，IrDA，LIN，SPI，UART/USART 外围设备:DMA，PDR，POR，PVD，PWM，温度传感器，WDT 输入/输出数:26 程序存储器容量:64KB（64K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:10K x 8 电压 - 电源 (Vcc/Vdd):2 V ~ 3.6 V 数据转换器:A/D 10x12b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:36-VFQFN，36-VFQFPN 包装:托盘 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名称:497-9032STM32F101T8U6-ND |
| P87C5820SF76 | 功能描述:IC MCU 8BIT 32K 20MHZ OTP 40-DIP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:87C 标准包装:160 系列:HCS12 核心处理器:HCS12 芯体尺寸:16-位 速度:25MHz 连通性:CAN，EBI/EMI，SCI，SPI 外围设备:POR，PWM，WDT 输入/输出数:35 程序存储器容量:128KB（128K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:4K x 8 电压 - 电源 (Vcc/Vdd):2.35 V ~ 5.5 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:52-LQFP 包装:托盘 |
| P87C5833SF76 | 功能描述:IC MCU 8BIT 32K 33MHZ OTP 40-DIP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:87C 标准包装:160 系列:HCS12 核心处理器:HCS12 芯体尺寸:16-位 速度:25MHz 连通性:CAN，EBI/EMI，SCI，SPI 外围设备:POR，PWM，WDT 输入/输出数:35 程序存储器容量:128KB（128K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:4K x 8 电压 - 电源 (Vcc/Vdd):2.35 V ~ 5.5 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:52-LQFP 包装:托盘 |
| P87C58SBAA | 制造商: 功能描述: 制造商:PHILIP 功能描述: |
| P87C58X2BA,512 | 功能描述:8位微控制器 -MCU 32K/256 OTP 12/6 CLK COMM PLCC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。