- 您现在的位置：买卖IC网 > PDF目录11181 > P87LPC764BDH,518 (NXP Semiconductors)IC 80C51 MCU 4K OTP 20-TSSOP PDF资料下载
参数资料
| 型号： | P87LPC764BDH,518 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 19/60页 |
| 文件大小： | 0K |
| 描述： | IC 80C51 MCU 4K OTP 20-TSSOP |
| 标准包装： | 2,500 |
| 系列： | LPC700 |
| 核心处理器： | 8051 |
| 芯体尺寸： | 8-位 |
| 速度： | 20MHz |
| 连通性： | I²C，UART/USART |
| 外围设备： | 欠压检测/复位，LED，POR，WDT |
| 输入/输出数： | 18 |
| 程序存储器容量： | 4KB（4K x 8） |
| 程序存储器类型： | OTP |
| RAM 容量： | 128 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 6 V |
| 振荡器型： | 内部 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 包装： | 带卷 (TR) |
| 其它名称： | P87LPC764BDH518 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页
Philips Semiconductors
Product data
P87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kbyte OTP
2003 Sep 03
25
For correct activation of Brownout Detect, the VDD fall time must be
no faster than 50 mV/
s. When VDD is restored, is should not rise
faster than 2 mV/
s in order to insure a proper reset.
The brownout voltage (2.5 V or 3.8 V) is selected via the BOV bit in
the EPROM configuration register UCFG1. When unprogrammed
(BOV = 1), the brownout detect voltage is 2.5 V. When programmed
(BOV = 0), the brownout detect voltage is 3.8 V.
If the Brownout Detect function is not required in an application, it
may be disabled, thus saving power. Brownout Detect is disabled by
setting the control bit BOD in the AUXR1 register (AUXR1.6).
Power On Detection
The Power On Detect has a function similar to the Brownout Detect,
but is designed to work as power comes up initially, before the
power supply voltage reaches a level where Brownout Detect can
work. When this feature is activated, the POF flag in the PCON
register is set to indicate an initial power up condition. The POF flag
will remain set until cleared by software.
Power Reduction Modes
The P87LPC764 supports Idle and Power Down modes of power
reduction.
Idle Mode
The Idle mode leaves peripherals running in order to allow them to
activate the processor when an interrupt is generated. Any enabled
interrupt source or Reset may terminate Idle mode. Idle mode is
entered by setting the IDL bit in the PCON register (see Figure 19).
Power Down Mode
The Power Down mode stops the oscillator in order to absolutely
minimize power consumption. Power Down mode is entered by
setting the PD bit in the PCON register (see Figure 19).
The processor can be made to exit Power Down mode via Reset or
one of the interrupt sources shown in Table 5. This will occur if the
interrupt is enabled and its priority is higher than any interrupt
currently in progress.
In Power Down mode, the power supply voltage may be reduced to
the RAM keep-alive voltage VRAM. This retains the RAM contents
at the point where Power Down mode was entered. SFR contents
are not guaranteed after VDD has been lowered to VRAM, therefore
it is recommended to wake up the processor via Reset in this case.
VDD must be raised to within the operating range before the Power
Down mode is exited. Since the watchdog timer has a separate
oscillator, it may reset the processor upon overflow if it is running
during Power Down.
Note that if the Brownout Detect reset is enabled, the processor will
be put into reset as soon as VDD drops below the brownout voltage.
If Brownout Detect is configured as an interrupt and is enabled, it will
wake up the processor from Power Down mode when VDD drops
below the brownout voltage.
When the processor wakes up from Power Down mode, it will start
the oscillator immediately and begin execution when the oscillator is
stable. Oscillator stability is determined by counting 1024 CPU
clocks after start-up when one of the crystal oscillator configurations
is used, or 256 clocks after start-up for the internal RC or external
clock input configurations.
Some chip functions continue to operate and draw power during
Power Down mode, increasing the total power used during Power
Down. These include the Brownout Detect, Watchdog Timer, and
Comparators.
BIT
SYMBOL
FUNCTION
PCON.7
SMOD1
When set, this bit doubles the UART baud rate for modes 1, 2, and 3.
PCON.6
SMOD0
This bit selects the function of bit 7 of the SCON SFR. When 0, SCON.7 is the SM0 bit. When 1,
SCON.7 is the FE (Framing Error) flag. See Figure 28 for additional information.
PCON.5
BOF
Brown Out Flag. Set automatically when a brownout reset or interrupt has occurred. Also set at
power on. Cleared by software. Refer to the Power Monitoring Functions section for additional
information.
PCON.4
POF
Power On Flag. Set automatically when a power-on reset has occurred. Cleared by software. Refer
to the Power Monitoring Functions section for additional information.
PCON.3
GF1
General purpose flag 1. May be read or written by user software, but has no effect on operation.
PCON.2
GF0
General purpose flag 0. May be read or written by user software, but has no effect on operation.
PCON.1
PD
Power Down control bit. Setting this bit activates Power Down mode operation. Cleared when the
Power Down mode is terminated (see text).
PCON.0
IDL
Idle mode control bit. Setting this bit activates Idle mode operation. Cleared when the Idle mode is
terminated (see text).
IDL
SU01475
PD
GF0
GF1
POF
BOF
SMOD0
SMOD1
0
1
2
3
4
5
6
7
PCON
Reset Value:
S 30h for a Power On reset
S 20h for a Brownout reset
S 00h for other reset sources
Not Bit Addressable
Address: 87h
Figure 19. Power Control Register (PCON)
相关PDF资料 |
PDF描述 |
|---|---|
| NLAST44599MNG | IC SWITCH DUAL DPDT 16QFN |
| PI5V330SWE | IC VIDEO MUX/DEMUX 2X1 16SOIC |
| DG442DYZ-T | IC SWITCH QUAD SPST 16SOIC |
| NLAS44599MNG | IC SWITCH DUAL DPDT 16QFN |
| ISL84714IHZ-T7A | IC SWITCH SPDT SC70-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P87LPC764BN | 制造商:NXP Semiconductors 功能描述:IC 8BIT MCU 87LC764 DIP20 制造商:NXP Semiconductors 功能描述:IC, 8BIT MCU, 87LC764, DIP20 制造商:NXP Semiconductors 功能描述:IC, 8BIT MCU, 80C51, 20MHZ, DIP-20; Controller Family/Series:(8051) 8052; Core Size:8bit; No. of I/O's:18; Supply Voltage Min:2.7V; Supply Voltage Max:6V; Digital IC Case Style:DIP; No. of Pins:20; Program Memory Size:4KB ;RoHS Compliant: Yes 制造商:NXP Semiconductors 功能描述:P87LPC764BN 8bit microcontroller,20MHz 制造商:NXP Semiconductors 功能描述:MCU 8-Bit 87LP 80C51 CISC 4KB EPROM 5V 20-Pin PDIP |
| P87LPC764BN,112 | 功能描述:8位微控制器 -MCU 80C51 4K/128 OTP RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| P87LPC764BN112 | 制造商:NXP Semiconductors 功能描述:IC 8BIT MCU 80C51 20MHZ DIP-20 |
| P87LPC764FD | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Low power, low price, low pin count 20 pin microcontroller with 4 kbyte OTP |
| P87LPC764FD,512 | 功能描述:8位微控制器 -MCU 4K/128 OTP 2.7-6V EXT SO20 RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。