参数资料
型号: P89C668
厂商: NXP Semiconductors N.V.
英文描述: 80C51 8-bit Flash microcontroller family 64KB ISP FLASH with 8KB RAM
中文描述: 80C51的8位闪存微控制器系列的ISP的64KB闪存与8KB的RAM的
文件页数: 17/54页
文件大小: 299K
代理商: P89C668
Philips Semiconductors
Preliminary data
P89C668
80C51 8-bit Flash microcontroller family
64KB ISP Flash with 8KB RAM
2001 Jul 27
17
S0CON
Address = 98H
Reset Value = 0000 0000B
SM0/FE
7
SM1
6
SM2
5
REN
4
TB8
3
RB8
2
Tl
1
Rl
0
Bit Addressable
(SMOD0 = 0/1)*
Symbol
Function
FE
Framing Error bit. This bit is set by the receiver when an invalid stop bit is detected. The FE bit is not cleared by valid
frames but should be cleared by software. The SMOD0 bit must be set to enable access to the FE bit.
Serial Port Mode Bit 0, (SMOD0 must = 0 to access bit SM0)
Serial Port Mode Bit 1
SM0
SM1
Mode
Description
Baud Rate**
0
0
0
shift register
f
OSC
/6
0
1
1
8-bit UART
variable
1
0
2
9-bit UART
f
OSC
/32 or f
OSC
/16
1
1
3
9-bit UART
variable
Enables the Automatic Address Recognition feature in Modes 2 or 3. If SM2 = 1 then Rl will not be set unless the
received 9th data bit (RB8) is 1, indicating an address, and the received byte is a Given or Broadcast Address.
In Mode 1, if SM2 = 1 then Rl will not be activated unless a valid stop bit was received, and the received byte is a
Given or Broadcast Address. In Mode 0, SM2 should be 0.
Enables serial reception. Set by software to enable reception. Clear by software to disable reception.
The 9th data bit that will be transmitted in Modes 2 and 3. Set or clear by software as desired.
In modes 2 and 3, the 9th data bit that was received. In Mode 1, if SM2 = 0, RB8 is the stop bit that was received.
In Mode 0, RB8 is not used.
Transmit interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or at the beginning of the stop bit in the
other modes, in any serial transmission. Must be cleared by software.
Receive interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or halfway through the stop bit time in
the other modes, in any serial reception (except see SM2). Must be cleared by software.
SM0
SM1
SM2
REN
TB8
RB8
Tl
Rl
NOTE:
*SMOD0 is located at PCON6.
**f
OSC
= oscillator frequency
SU01457
Bit:
Figure 7. S0CON: Serial Port Control Register
相关PDF资料
PDF描述
P89C668HBBD 80C51 8-bit Flash microcontroller family 64KB ISP FLASH with 8KB RAM
P89CE558 Single-chip 8-bit microcontroller(8位单片微控制器)
P83CE558 Single-chip 8-bit microcontroller
P89CE558EBB Single-chip 8-bit microcontroller
P89CE558EFB Single-chip 8-bit microcontroller
相关代理商/技术参数
参数描述
P89C668HBA 功能描述:8位微控制器 -MCU 80C51 64K FL / 8K RM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
P89C668HBA/00,512 功能描述:8位微控制器 -MCU 64K/8K FL 6 CLK ISP/IAP PLCC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
P89C668HBBD 功能描述:8位微控制器 -MCU 80C51 64K FL / 8K RM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
P89C668HBBD/00,557 功能描述:8位微控制器 -MCU 64K/8K FL 6CLK ISP/IAP QFP COM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
P89C668HFA 功能描述:8位微控制器 -MCU 80C51 64K FL / 8K RM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT