- 您现在的位置：买卖IC网 > PDF目录296762 > P89LPC931A1FDH (NXP SEMICONDUCTORS) 8-bit microcontroller with accelerated two-clock 80C51 core 4 kB-8 kB 3 V byte-erasable flash PDF资料下载
参数资料
| 型号： | P89LPC931A1FDH |
| 厂商： | NXP SEMICONDUCTORS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-bit microcontroller with accelerated two-clock 80C51 core 4 kB-8 kB 3 V byte-erasable flash |
| 中文描述： | 8-BIT, FLASH, 18 MHz, MICROCONTROLLER, PDSO28 |
| 封装： | 4.40 MM, PLASTIC, MO-153, SOT-361, TSSOP-28 |
| 文件页数： | 17/66页 |
| 文件大小： | 1326K |
| 代理商： | P89LPC931A1FDH |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页
P89LPC9301_931A1
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 29 November 2010
24 of 66
NXP Semiconductors
P89LPC9301/931A1
8-bit microcontroller with accelerated two-clock 80C51 core
An open-drain port pin has a Schmitt trigger input that also has a glitch suppression
circuit.
7.16.1.3
Input-only configuration
The input-only port configuration has no output drivers. It is a Schmitt trigger input that
also has a glitch suppression circuit.
7.16.1.4
Push-pull output configuration
The push-pull output configuration has the same pull-down structure as both the
open-drain and the quasi-bidirectional output modes, but provides a continuous strong
pull-up when the port latch contains a logic 1. The push-pull mode may be used when
more source current is needed from a port output. A push-pull port pin has a
Schmitt triggered input that also has a glitch suppression circuit. The P89LPC9301/931A1
device has high current source on eight pins in push-pull mode. See Table 9 “Limiting
7.16.2 Port 0 analog functions
The P89LPC9301/931A1 incorporates two Analog Comparators. In order to give the best
analog function performance and to minimize power consumption, pins that are being
used for analog functions must have the digital outputs and digital inputs disabled.
Digital outputs are disabled by putting the port output into the Input-Only
(high-impedance) mode.
Digital inputs on Port 0 may be disabled through the use of the PT0AD register, bits 1:5.
On any reset, PT0AD[1:5] defaults to logic 0s to enable digital functions.
7.16.3 Additional port features
After power-up, all pins are in Input-Only mode. Please note that this is different from
the LPC76x series of devices.
After power-up, all I/O pins except P1.5, may be configured by software.
Pin P1.5 is input only. Pins P1.2 and P1.3 are configurable for either input-only or
open-drain.
Every output on the P89LPC9301/931A1 has been designed to sink typical LED drive
current. However, there is a maximum total output current for all ports which must not be
exceeded. Please refer to Table 10 “Static characteristics” for detailed specifications.
All ports pins that can function as an output have slew rate controlled outputs to limit noise
generated by quickly switching output signals. The slew rate is factory-set to
approximately 10 ns rise and fall times.
7.17 Power monitoring functions
The P89LPC9301/931A1 incorporates power monitoring functions designed to prevent
incorrect operation during initial power-up and power loss or reduction during operation.
This is accomplished with two hardware functions: Power-on detect and brownout detect.
相关PDF资料 |
PDF描述 |
|---|---|
| P89LPC930FDH | 8-bit microcontrollers with two-clock 80C51 core 4 kB-8 kB 3 V Flash with 256-byte data RAM |
| P89LPC931FDH | 8-bit microcontrollers with two-clock 80C51 core 4 kB-8 kB 3 V Flash with 256-byte data RAM |
| P89LPC9321FDH | 8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable flash with 512-byte data EEPROM |
| P89LPC932A1FDH | 8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable flash with 512-byte data EEPROM |
| P89LPC932A1FHN | 8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable flash with 512-byte data EEPROM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P89LPC931A1FDH,512 | 功能描述:8位微控制器 -MCU IC 80C51 MCU FLASH 8K RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| P89LPC931FDH | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit microcontrollers with two-clock 80C51 core 4 kB/8 kB 3 V Flash with 256-byte data RAM |
| P89LPC931FDH,112 | 功能描述:8位微控制器 -MCU 80C51 8K FL 256B RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| P89LPC931FDH,129 | 功能描述:8位微控制器 -MCU 8K FL/256B RAM/I2C/SPI/TSSOP28 RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| P89LPC931FDH.129 | 制造商:NXP Semiconductors 功能描述:IC 8BIT MCU 8K FLASH SMD 89LC931 |
发布紧急采购，3分钟左右您将得到回复。