- 您现在的位置：买卖IC网 > PDF目录3795 > P89LPC932A1FDH,512 (NXP Semiconductors)IC 80C51 MCU FLASH 8K 28-TSSOP PDF资料下载
参数资料
| 型号： | P89LPC932A1FDH,512 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 16/64页 |
| 文件大小： | 0K |
| 描述： | IC 80C51 MCU FLASH 8K 28-TSSOP |
| 标准包装： | 51 |
| 系列： | LPC900 |
| 核心处理器： | 8051 |
| 芯体尺寸： | 8-位 |
| 速度： | 18MHz |
| 连通性： | I²C，SPI，UART/USART |
| 外围设备： | 欠压检测/复位，LED，POR，PWM，WDT |
| 输入/输出数： | 26 |
| 程序存储器容量： | 8KB（8K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 768 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.4 V ~ 3.6 V |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 包装： | 管件 |
| 产品目录页面： | 706 (CN2011-ZH PDF) |
| 配用： | DB-TSSOP-LPC932-ND - BOARD FOR LPC932 TSSOP 622-1014-ND - BOARD FOR LPC9XX TSSOP 622-1008-ND - BOARD FOR LPC9103 10-HVSON 622-1006-ND - SOCKET ADAPTER BOARD 568-4000-ND - DEMO BOARD SPI/I2C TO DUAL UART 568-3510-ND - DEMO BOARD SPI/I2C TO UART 622-1003-ND - KIT FOR LCD DEMO 622-1002-ND - USB IN-CIRCUIT PROG LPC9XX 568-1759-ND - EMULATOR DEBUGGER/PROGRMMR LPC9X 568-1758-ND - BOARD EVAL FOR LPC93X MCU FAMILY |
| 其它名称： | 568-4515-5 935276132512 P89LPC932A1FDH P89LPC932A1FDH-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
P89LPC932A1_3
NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 03 — 12 March 2007
23 of 64
NXP Semiconductors
P89LPC932A1
8-bit microcontroller with accelerated two-clock 80C51 core
7.13.1.4
Push-pull output conguration
The push-pull output conguration has the same pull-down structure as both the
open-drain and the quasi-bidirectional output modes, but provides a continuous strong
pull-up when the port latch contains a logic 1. The push-pull mode may be used when
more source current is needed from a port output. A push-pull port pin has a Schmitt
trigger input that also has a glitch suppression circuit.
7.13.2 Port 0 analog functions
The P89LPC932A1 incorporates two Analog Comparators. In order to give the best
analog function performance and to minimize power consumption, pins that are being
used for analog functions must have the digital outputs and digital inputs disabled.
Digital outputs are disabled by putting the port output into the Input-only (high-impedance)
mode.
Digital inputs on Port 0 may be disabled through the use of the PT0AD register, bits 1:5.
On any reset, PT0AD[1:5] defaults to logic 0s to enable digital functions.
7.13.3 Additional port features
After power-up, all pins are in Input-only mode. Please note that this is different from
the LPC76x series of devices.
After power-up, all I/O pins except P1.5, may be congured by software.
Pin P1.5 is input only. Pins P1.2 and P1.3 and are congurable for either input-only or
open-drain.
Every output on the P89LPC932A1 has been designed to sink typical LED drive current.
However, there is a maximum total output current for all ports which must not be
exceeded. Please refer to Table 8 “Static characteristics” for detailed specications.
All ports pins that can function as an output have slew rate controlled outputs to limit noise
generated by quickly switching output signals. The slew rate is factory-set to
approximately 10 ns rise and fall times.
7.14 Power monitoring functions
The P89LPC932A1 incorporates power monitoring functions designed to prevent
incorrect operation during initial power-up and power loss or reduction during operation.
This is accomplished with two hardware functions: Power-on detect and brownout detect.
7.14.1 Brownout detection
The brownout detect function determines if the power supply voltage drops below a
certain level. The default operation is for a brownout detection to cause a processor reset,
however it may alternatively be congured to generate an interrupt.
Brownout detection may be enabled or disabled in software.
If brownout detection is the brownout condition occurs when VDD falls below the brownout
above Vbo. If the P89LPC932A1 device is to operate with a power supply that can be
below 2.7 V, BOE should be left in the unprogrammed state so that the device can operate
at 2.4 V, otherwise continuous brownout reset may prevent the device from operating.
相关PDF资料 |
PDF描述 |
|---|---|
| P89LPC932A1FDH,529 | IC 80C51 MCU FLASH 8K 28-TSSOP |
| P87C51SBAA,512 | IC 80C51 MCU 4K OTP 44-PLCC |
| LPC1342FHN33,551 | IC MCU 32BIT 16KB FLASH 33HVQFN |
| LPC11U13FBD48/201, | IC MCU 32BIT 24K 48LQFP |
| LPC11C12FBD48/301, | IC MCU 32BIT 16KB FLASH 48LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P89LPC932A1FHN | 制造商:NXP Semiconductors 功能描述:MCU 8BIT 80C51 8K FLASH HVQFN-28 |
| P89LPC932A1FHN,151 | 功能描述:8位微控制器 -MCU 80C51 8K FL 768B RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| P89LPC932A1FHN151 | 制造商:NXP Semiconductors 功能描述:IC 8BIT MCU 80C51 18MHZ 28-HVQFN |
| P89LPC932A1FN | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable flash with 512-byte data EEPROM |
| P89LPC932BA | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:80C51 8-bit microcontroller with two-clock core 8 KB 3 V low-power Flash with 512-byte data EEPROM |
发布紧急采购，3分钟左右您将得到回复。