- 您现在的位置：买卖IC网 > Datasheet目录240 > PAXLCL00 (Red Lion Controls)METER CURRENT LOOP 3 1/2-DIGIT Datasheet资料下载
参数资料
| 型号： | PAXLCL00 |
| 厂商： | Red Lion Controls |
| 文件页数： | 4/8页 |
| 文件大小： | 0K |
| 描述： | METER CURRENT LOOP 3 1/2-DIGIT |
| 产品目录绘图： | PAX Lite Series PAX Lite Series Cut Out |
| 标准包装： | 1 |
| 系列： | PAX®LITE |
| 类型： | 过程多用表（4-20mA 回路） |
| 测量范围： | 4-20mA 回路 |
| 显示器样式： | 红色字符，黑色背景 |
| 显示器类型： | LED |
| 显示器正面尺寸： | 3.80" L x 1.95" W（96.5 x 49.5mm） |
| 显示器位数： | 3.5 |
| 显示器位数 - 高度： | 0.560"（14.22mm） |
| 背光： | 无 |
| 安装类型： | 面板安装 |
| 端子： | 端接块 |
| 电源电压： | 85 ~ 250VAC |
| 产品目录页面： | 2853 (CN2011-ZH PDF) |
| 其它名称： | RLC112 |
1.0 I NSTALLING
THE
M ETER
Installation
The PAX meets NEMA 4X/IP65 requirements when properly installed. The
unit is intended to be mounted into an enclosed panel. Prepare the panel cutout
to the dimensions shown. Remove the panel latch from the unit. Slide the panel
gasket over the rear of the unit to the back of the bezel. The unit should be
installed fully assembled. Insert the unit
into the panel cutout.
PANEL
BEZEL
While holding the unit in place, push the panel latch over the rear of the unit
so that the tabs of the panel latch engage in the slots on the case. The panel latch
should be engaged in the farthest forward slot possible. To achieve a proper seal,
tighten the latch screws evenly until the unit is snug in the panel (Torque to
approximately 7 in-lbs [79N-cm]). Do not over-tighten the screws.
Installation Environment
The unit should be installed in a location that does not exceed the maximum
operating temperature and provides good air circulation. Placing the unit near
devices that generate excessive heat should be avoided.
The bezel should be cleaned only with a soft cloth and neutral soap product.
Do NOT use solvents. Continuous exposure to direct sunlight may accelerate the
LATCHING
SLOTS
PANEL
LATCH
LATCHING
aging process of the bezel.
PANEL CUT-OUT
TABS
-.00
3.62 +.03
PANEL
GASKET
PANEL
MOUNTING
SCREWS
-.0
(92 +.8 )
-.00
-.0
1.77 +.02
(45 +.5 )
2.0 S ETTING
THE
S WITCHES
The meter has switches, which must be checked and/or changed prior to
applying power. To access the switches, remove the meter base from the case by
firmly squeezing and pulling back on the side rear finger tabs. This should lower
the latch below the case slot (which is located just in front of the finger tabs). It
FRONT DISPLAY
is recommended to release the latch on one side, then start the other side latch.
Main
4
Set-Up DIP Switches
Two banks of DIP switches are located inside the meter. The 10 position bank
Circuit
Board
3
2
1
ON
D.P./ BACKLIGHT
of switches are used for calibrating the meter. The values of these switches are
discussed in section 5.0 Calibrating the Meter.
The bank of 4 switches located near the front display are used for the
selection of decimal points and backlight annunciator. Selecting “ON” position
1
2
ON
enables the function.
3
4
5
OFFSET
SWITCH
1
FUNCTION
Decimal Point 1 (000.0)
6
7
8
9
SPAN
10
2
3
4
Decimal Point 2 (00.00)
Decimal Point 3 (0.000)
Backlight Annunciator for Units Label
REAR TERMINALS
OFFSET
SPAN
3.0 W IRING
WIRING OVERVIEW
THE
M ETER
Electrical connections are made via screw-clamp terminals located on the
back of the meter. All conductors should conform to the meter ’s voltage and
current ratings. All cabling should conform to appropriate standards of good
installation, local codes and regulations. It is recommended that power supplied
to the meter (AC) be protected by a fuse or circuit breaker.
4
When wiring the meter, compare the numbers embossed on the back of the
meter case against those shown in wiring drawings for proper wire position. Strip
the wire, leaving approximately 0.3" (7.5 mm) bare lead exposed (stranded wires
should be tinned with solder). Insert the lead under the correct screw-clamp
terminal and tighten until the wire is secure. (Pull wire to verify tightness.)
相关PDF资料 |
PDF描述 |
|---|---|
| PAXLHV00 | METER AC VOLT 3-DIGIT PNL MNT |
| PAXLIA00 | METER AC CURRENT 3 1/2-DIGIT |
| PAXLIT00 | METER AC CURRENT 5A 3 1/2-DIGIT |
| PAXLPV00 | METER PROCESS VOLT 3 1/2-DIGIT |
| PAXLRT00 | METER RTD TEMP 4-DIGIT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PAXLCR00 | 制造商:Red Lion Controls 功能描述:Counter; Rate Meter; LCD; 6 Digit, 50-250VDC 制造商:Red Lion Controls 功能描述:COUNT/RATE METER |
| PAXLCRU0 | 制造商:Red Lion Controls 功能描述:UL LISTED CURRENT/RATE METER 制造商:Red Lion Controls 功能描述:PAXL UL COUNT,RATE |
| PAXLHV00 | 功能描述:METER AC VOLT 3-DIGIT PNL MNT RoHS:是 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:PAX®LITE 标准包装:12 系列:* 其它名称:Q7072030 |
| PAXLIA00 | 功能描述:METER AC CURRENT 3 1/2-DIGIT RoHS:是 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:PAX®LITE 标准包装:12 系列:* 其它名称:Q7072030 |
| PAXLID00 | 功能描述:METER DC CURRENT 3 1/2-DIGIT RoHS:是 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:PAX®LITE 标准包装:12 系列:* 其它名称:Q7072030 |
发布紧急采购，3分钟左右您将得到回复。