- 您现在的位置：买卖IC网 > Datasheet目录240 > PAXLVD00 (Red Lion Controls)VOLTMETER DC 3 1/2-DIGIT Datasheet资料下载
参数资料
| 型号： | PAXLVD00 |
| 厂商： | Red Lion Controls |
| 文件页数： | 5/8页 |
| 文件大小： | 0K |
| 描述： | VOLTMETER DC 3 1/2-DIGIT |
| 产品目录绘图： | PAX Lite Series PAX Lite Series Cut Out |
| 标准包装： | 1 |
| 系列： | PAX®LITE |
| 类型： | 伏特表 |
| 测量范围： | 0 ~ 300V |
| 显示器样式： | 红色字符，黑色背景 |
| 显示器类型： | LED |
| 显示器正面尺寸： | 3.80" L x 1.95" W（96.5 x 49.5mm） |
| 显示器位数： | 3.5 |
| 显示器位数 - 高度： | 0.560"（14.22mm） |
| 背光： | 无 |
| 安装类型： | 面板安装 |
| 端子： | 端接块 |
| 电源电压： | 115VAC，230 VAC |
| 产品目录页面： | 2853 (CN2011-ZH PDF) |
| 其它名称： | RLC107 |
PAXLV Jumper Selection
FRONT DISPLAY
JUMPER SELECTIONS
Main
The
indicates factory setting.
Circuit
Board
ON
5
4
3
2
1
INPUT RANGE JUMPER
SET-UP
ONLY ONE
DIP
SWITCHES
JUMPER IN
THIS AREA!
±1.999V
±19.99V
±199.9V
POWER
SCALING
POT
VOLT
±300V
SELECTION
SWITCH
INPUT RANGE
JUMPER
REAR TERMINALS
REAR TERMINALS
3.0 W IRING
THE
M ETER
WIRING OVERVIEW
Electrical connections are made via screw-clamp terminals located on the
back of the meter. All conductors should conform to the meter ’s voltage and
current ratings. All cabling should conform to appropriate standards of good
installation, local codes and regulations. It is recommended that power supplied
to the meter (AC) be protected by a fuse or circuit breaker.
When wiring the meter, compare the numbers embossed on the back of the
meter case against those shown in wiring drawings for proper wire position. Strip
the wire, leaving approximately 0.3" (7.5 mm) bare lead exposed (stranded wires
should be tinned with solder). Insert the lead under the correct screw-clamp
terminal and tighten until the wire is secure. (Pull wire to verify tightness.)
EMC INSTALLATION GUIDELINES
Although this meter is designed with a high degree of immunity to Electro-
Magnetic Interference (EMI), proper installation and wiring methods must be
followed to ensure compatibility in each application. The type of the electrical
noise, its source or the method of coupling into the unit may be different for
various installations. Listed below are some EMC guidelines for successful
installation in an industrial environment.
1. The meter should be mounted in a metal enclosure, which is properly
connected to protective earth.
2. Never run Signal or Control cables in the same conduit or raceway with AC
power lines, conductors feeding motors, solenoids, SCR controls, and
heaters, etc. The cables should be run in metal conduit that is properly
grounded. This is especially useful in applications where cable runs are long
and portable two-way radios are used in close proximity or if the installation
is near a commercial radio transmitter.
3. Signal or Control cables within an enclosure should be routed as far away as
possible from contactors, control relays, transformers, and other noisy
components.
5
4. In extremely high EMI environments, the use of external EMI suppression
devices, such as ferrite suppression cores, is effective. Install them on Signal
and Control cables as close to the unit as possible. Loop the cable through the
core several times or use multiple cores on each cable for additional protection.
Install line filters on the power input cable to the unit to suppress power line
interference. Install them near the power entry point of the enclosure. The
following EMI suppression devices (or equivalent) are recommended:
Ferrite Suppression Cores for signal and control cables:
Fair-Rite # 0443167251 (RLC #FCOR0000)
TDK # ZCAT3035-1330A
Steward #28B2029-0A0
Line Filters for input power cables:
Schaffner # FN610-1/07 (RLC #LFIL0000)
Schaffner # FN670-1.8/07
Corcom #1VR3
Note: Reference manufacturer ’s instructions when installing a line filter.
5. Long cable runs are more susceptible to EMI pickup than short cable runs.
Therefore, keep cable runs as short as possible.
6. Switching of inductive loads produces high EMI. Use of snubbers across
inductive loads suppresses EMI.
Snubber: RLC#SNUB0000.
相关PDF资料 |
PDF描述 |
|---|---|
| PAXTM100 | TIMER DISPLAY 1/8 DIN PRESET 6 D |
| PB-1583-TF | BOX ABS 4.37X3.12X2" BK 1=10PCS |
| PB-1583 | BOX ABS 4.37X3.12X2" BK 1=10PCS |
| PBS-11273 | BOX ABS 6.30" X 3.75" X 1.41" BK |
| PBS-11275 | BOX ABS 6.30" X 3.75" X 1.41" BK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PAXOEMS1 | 制造商:Red Lion Controls 功能描述:SOFTWARE AND USB CABLE RS232 |
| PAXOEMSS | 制造商:Red Lion Controls 功能描述:SOFTWARE AND CABLE RS232 制造商:Red Lion Controls 功能描述:SOFTWARE AND CABLE, RS232 制造商:Red Lion Controls 功能描述:SOFTWARE AND CABLE, RS232; For Use With:PAXI Counter Display; SVHC:No SVHC (19-Dec-2012) ;RoHS Compliant: Yes |
| PAXP0000 | 制造商:Red Lion Controls 功能描述:Meter, Process, 5 Digit .56" Red LED Display, Power: 85-250 VAC 制造商:Red Lion Controls 功能描述:PROCESS INPUT FIELD 制造商:Red Lion Controls 功能描述:Process Meter 制造商:Red Lion Controls 功能描述:PROCESS METER, 85VAC TO 250VAC; No. of Digits / Alpha:5; Meter Function:DC Milliamps / DC Volts; Meter Range:-2mA to +26mA / -1V to +13V; Digit Height:14.2mm; Panel Cutout Height:44.96mm; Panel Cutout Width:91.95mm ;RoHS Compliant: Yes |
| PAXP0010 | 制造商:Red Lion Controls 功能描述:Panel Meter; 0.56 in.; 11 to 36 VDC, 24 VAC; 0 to degC; -40 to degC 制造商:Red Lion Controls 功能描述:DC PROCESS INPUT FIELD 制造商:Red Lion Controls 功能描述:Process Meter 制造商:Red Lion Controls 功能描述:PROCESS METER; No. of Digits / Alpha:5; Meter Function:DC Milliamps / DC Volts; Meter Range:-2mA to +26mA / -1V to +13V; Digit Height:14.2mm; Panel Cutout Height:44.96mm; Panel Cutout Width:91.95mm; Power Consumption:11W ;RoHS Compliant: NA |
| PAXP0100 | 制造商:Red Lion Controls 功能描述:METER, PROCESS IN, FIELD UPGRAD GRN PAX 制造商:Red Lion Controls 功能描述:PROCESS INPUT FIELD |
发布紧急采购，3分钟左右您将得到回复。