参数资料
| 型号： | PCA8574TS,118 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 32/32页 |
| 文件大小： | 0K |
| 描述： | IC I/O EXPANDER I2C 8B 20SSOP |
| 特色产品： | NXP - I2C Interface |
| 标准包装： | 1 |
| 接口： | I²C |
| 输入/输出数： | 8 |
| 中断输出： | 是 |
| 频率 - 时钟： | 400kHz |
| 电源电压： | 2.3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-LSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 标准包装 |
| 包括： | POR |
| 其它名称： | 568-8700-6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页
PCA8574_PCA8574A
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 3 — 3 June 2013
9 of 32
NXP Semiconductors
PCA8574; PCA8574A
Remote 8-bit I/O expander for I2C-bus with interrupt
Simple code WRITE mode:
<S> <slave address + write> <ACK> <data out> <ACK> <data out> <ACK> ...
<data out> <ACK> <P>
Remark: Bold type = generated by slave device.
8.3 Reading from a port (Input mode)
The port must have been previously written to logic 1, which is the condition after
power-on reset. To enter the Read mode the master (microcontroller) addresses the slave
device and sets the last bit of the address byte to logic 1 (address byte read). The slave
will acknowledge and then send the data byte to the master. The master will NACK and
then send the STOP condition or ACK and read the input register again.
The read of any pin being used as an output will indicate HIGH or LOW depending on the
actual state of the input pin.
If the data on the input port changes faster than the master can read, this data may be
lost. The DATA 2 and DATA 3 are lost because these data did not meet the setup time and
hold time (see Figure 9).
Simple code for Read mode:
<S> <slave address + read> <ACK> <data in> <ACK> ... <data in> <ACK> <data in>
<NACK> <P>
Remark: Bold type = generated by slave device.
A LOW-to-HIGH transition of SDA while SCL is HIGH is defined as the STOP condition (P). Transfer of data can be stopped at
any moment by a STOP condition. When this occurs, data present at the last acknowledge phase is valid (output mode). Input
data is lost.
Fig 9.
Read mode (input)
A5 A4 A3 A2 A1 A0
1
A
SA6
slave address
START condition
R/W
acknowledge
from slave
002aah383
data from port
A
acknowledge
from master
SDA
1
no acknowledge
from master
read from
port
data at
port
data from port
DATA 1
DATA 4
INT
DATA 4
DATA 2
DATA 3
P
STOP
condition
tv(INT)
trst(INT)
th(D)
tsu(D)
trst(INT)
DATA 1
相关PDF资料 |
PDF描述 |
|---|---|
| PCA8574APW,112 | IC I/O EXPANDER I2C 8B 16TSSOP |
| PCA9554N,112 | IC I/O EXPANDER I2C 8B 16DIP |
| PCA9557D,112 | IC I/O EXPANDER I2C 8B 16SOIC |
| PCA9554AN,112 | IC I/O EXPANDER I2C 8B 16DIP |
| 423-047-520-102 | CONN PLUG 47POS .200X.300 GOLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCA8574TS-T | 功能描述:接口-I/O扩展器 8-BIT I2C FM QB GPIO INT PU RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| PCA8575 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Remote 16-bit I/O expander for I2C-bus with interrupt |
| PCA8575BQ | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Remote 16-bit I/O expander for I2C-bus with interrupt |
| PCA8575BQ,118 | 功能描述:接口-I/O扩展器 16-BIT I2C FM QB RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| PCA8575BQ-T | 功能描述:接口-I/O扩展器 16-BIT I2C FM QB GPIO INT PU RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。