参数资料
| 型号： | PCA9501D,112 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 27/28页 |
| 文件大小： | 0K |
| 描述： | IC I/O EXPANDER I2C 8B 20SOIC |
| 标准包装： | 38 |
| 接口： | I²C，SM 总线 |
| 输入/输出数： | 8 |
| 中断输出： | 是 |
| 频率 - 时钟： | 400kHz |
| 电源电压： | 2.5 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 20-SO |
| 包装： | 管件 |
| 包括： | EEPROM |
| 配用： | 568-4002-ND - DEMO BOARD I2C |
| 其它名称： | 568-3353-5 935272364112 PCA9501D |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页
PCA9501_4
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 10 February 2009
8 of 28
NXP Semiconductors
PCA9501
8-bit I2C-bus and SMBus I/O port with interrupt, 2-kbit EEPROM
7.4 Memory operations
7.4.1 Write operations
Write operations require an additional address eld to indicate the memory address
location to be written. The address eld is eight bits long providing access to any one of
the 256 words of memory. There are two types of write operations, ‘byte write’ and ‘page
write’.
Write operation is possible when the Write Control pin (WC) is put at a LOW logic level (0).
When this control signal is set at 1, write operation is not possible and data in the memory
is protected.
‘Byte write’ and ‘page write’ explained below assume that WC is set to 0.
7.4.1.1
Byte write
To perform a byte write, the START condition is followed by the memory slave address and
the R/W bit set to 0. The PCA9501 will respond with an acknowledge and then consider
the next eight bits sent as the word address and the eight bits after the word address as
the data. The PCA9501 will issue an acknowledge after the receipt of both the word
address and the data. To terminate the data transfer the master issues the STOP
condition, initiating the internal write cycle to the non-volatile memory. Only write and read
operations to the quasi-bidirectional I/Os are allowed during the internal write cycle.
Fig 10. Application of multiple PCA9501s with interrupt
Fig 11. Interrupt generated by a change of input to IO5
002aad293
VDD
MICROCONTROLLER
INT
PCA9501
INT
PCA9501
INT
device 1
device 2
PCA9501
INT
device 16
1
A
S
slave address (I/O expander)
START condition
R/W
acknowledge
from slave
002aad294
1
data from port
1
12345678
SCL
9
SDA
data into IO5
INT
A5 A4 A3 A2 A1 A0
0
IO5
P
STOP
condition
tv(INT)
trst(INT)
相关PDF资料 |
PDF描述 |
|---|---|
| PCA9502BS,128 | IC I/O EXPANDER I2C/SPI 24HVQFN |
| PCA9505DGG,118 | IC I/O EXPANDER I2C 40B 56TSSOP |
| PCA9507D,118 | IC I/O EXPANDER I2C 24B 8SOIC |
| PCA9534PW,112 | IC I/O EXPANDER I2C 8B 16TSSOP |
| PCA9535BS1,118 | IC I/O EXPANDER I2C 16B 24HVQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCA9501PW | 功能描述:I2C 接口集成电路 I/O EXPANDER W/2K EE RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16 |
| PCA9501PW,112 | 功能描述:I2C 接口集成电路 I/O EXPANDER W/2K EE RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16 |
| PCA9501PW,118 | 功能描述:接口-I/O扩展器 8BIT I2C RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| PCA9501PW112 | 制造商:NXP Semiconductors 功能描述:IC I/O EXPANDER 8BIT 400KHZ TSSOP-20 |
| PCA9501PW118 | 制造商:Rochester Electronics LLC 功能描述: 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述: |
发布紧急采购，3分钟左右您将得到回复。