- 您现在的位置：买卖IC网 > PDF目录3778 > PCA9536DP/DG,118 (NXP Semiconductors)IC I/O EXPANDER I2C 4B 8TSSOP PDF资料下载
参数资料
| 型号： | PCA9536DP/DG,118 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 19/22页 |
| 文件大小： | 0K |
| 描述： | IC I/O EXPANDER I2C 4B 8TSSOP |
| 特色产品： | NXP - I2C Interface |
| 标准包装： | 1 |
| 接口： | I²C，SM 总线 |
| 输入/输出数： | 4 |
| 中断输出： | 无 |
| 频率 - 时钟： | 400kHz |
| 电源电压： | 2.3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 标准包装 |
| 包括： | POR |
| 其它名称： | 568-8252-6 |
PCA9536_5
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 05 — 25 January 2010
6 of 22
NXP Semiconductors
PCA9536
4-bit I2C-bus and SMBus I/O port
6.1.5 Register 3 - Configuration register
This register configures the directions of the I/O pins. If a bit in this register is set, the
corresponding port pin is enabled as an input with high-impedance output driver. If a bit in
this register is cleared, the corresponding port pin is enabled as an output. At reset, the
I/Os are configured as inputs with a weak pull-up to VDD.
‘Not used’ bits can be programmed with either logic 0 or logic 1.
6.2 Power-on reset
When power is applied to VDD, an internal Power-On Reset (POR) holds the PCA9536 in
a reset condition until VDD has reached VPOR. At that point, the reset condition is released
and the PCA9536 registers and state machine will initialize to their default states.
Thereafter, VDD must be lowered below 0.2 V to reset the device.
For a power reset cycle, VDD must be lowered below 0.2 V and then restored to the
operating voltage.
6.3 I/O port
When an I/O is configured as an input, FETs Q1 and Q2 are off, creating a
high-impedance input with a weak pull-up (100 k
Ω typical) to V
DD. The input voltage may
be raised above VDD to a maximum of 5.5 V.
If the I/O is configured as an output, then either Q1 or Q2 is enabled, depending on the
state of the Output Port register. Care should be exercised if an external voltage is applied
to an I/O configured as an output because of the low-impedance paths that exist between
the pin and either VDD or VSS.
Table 7.
Register 3 - Configuration register bit description
Legend: * default value
Bit
Symbol
Access
Value
Description
7
C7
R/W
1*
not used
6C6
R/W
1*
5C5
R/W
1*
4C4
R/W
1*
3
C3
R/W
1*
configures the directions of the I/O pins
0 = corresponding port pin enabled as an output
1 = corresponding port pin configured as input
(default value)
2C2
R/W
1*
1C1
R/W
1*
0C0
R/W
1*
相关PDF资料 |
PDF描述 |
|---|---|
| PCF8575TS/1,118 | IC I/O EXPANDER I2C 16B 24SSOP |
| PCA9539D,118 | IC I/O EXPANDER I2C 16B 24SOIC |
| PCA9555DB,118 | IC I/O EXPANDER I2C 16B 24SSOP |
| ATTINY13A-SFR | IC MCU AVR 1K FLASH 8SOIC |
| PCA9539PW,118 | IC I/O EXPANDER I2C 16B 24TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCA9536DR | 功能描述:接口-I/O扩展器 Remote 4-Bit I2C and SMBus I/O Expander RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| PCA9536DRG4 | 功能描述:接口-I/O扩展器 Remote 4-Bit I2C and SMBus I/O Expander RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| PCA9536DT | 制造商:TI 制造商全称:Texas Instruments 功能描述:REMOTE 4-BIT I2C AND SMBus I/O EXPANDER WITH CONFIGURATION REGISTERS |
| PCA9536TK | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:4-bit I2C-bus and SMBus I/O port |
| PCA9536TK,118 | 功能描述:接口-I/O扩展器 4-BIT I2C FM TP GPIO RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。