参数资料
| 型号： | PCA9538PW,112 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 33/34页 |
| 文件大小： | 0K |
| 描述： | IC I/O EXPANDER I2C 8B 16TSSOP |
| 标准包装： | 96 |
| 接口： | I²C，SM 总线 |
| 输入/输出数： | 8 |
| 中断输出： | 是 |
| 频率 - 时钟： | 400kHz |
| 电源电压： | 2.3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 管件 |
| 包括： | POR |
| 其它名称： | 935277419112 PCA9538PW PCA9538PW-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页当前第33页第34页
PCA9538
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 6 — 6 February 2013
8 of 34
NXP Semiconductors
PCA9538
8-bit I2C-bus and SMBus low power I/O port with interrupt and reset
6.2.5 Register 3 - Configuration register
This register configures the directions of the I/O pins. If a bit in this register is set, the
corresponding port pin is enabled as an input with high-impedance output driver. If a bit in
this register is cleared, the corresponding port pin is enabled as an output. At reset, the
I/Os are configured as inputs.
6.3 Power-on reset
When power is applied to VDD, an internal Power-On Reset (POR) holds the PCA9538 in
a reset condition until VDD has reached VPOR. At that point, the reset condition is released
and the PCA9538 registers and state machine will initialize to their default states.
Thereafter, VDD must be lowered below 0.2 V to reset the device.
For a power reset cycle, VDD must be lowered below 0.2 V and then restored to the
operating voltage.
6.4 RESET input
A reset can be accomplished by holding the RESET pin LOW for a minimum of tw(rst).
The PCA9538 registers and SMBus/I2C-bus state machine will be held in their default
state until the RESET input is once again HIGH. This input requires a pull-up resistor to
VDD if no active connection is used.
6.5 Interrupt output
The open-drain interrupt output (INT) is activated when one of the port pins changes state
and the pin is configured as an input. The interrupt is de-activated when the input returns
to its previous state or the Input Port register is read.
Note that changing an I/O from an output to an input may cause a false interrupt to occur
if the state of the pin does not match the contents of the Input Port register.
Table 8.
Register 3 - Configuration register bit description
Legend: * default value.
Bit
Symbol
Access
Value
Description
7
C7
R/W
1*
configures the directions of the I/O pins
0 = corresponding port pin enabled as an output
1 = corresponding port pin configured as an input
(default value)
6C6
R/W
1*
5C5
R/W
1*
4C4
R/W
1*
3C3
R/W
1*
2C2
R/W
1*
1C1
R/W
1*
0C0
R/W
1*
相关PDF资料 |
PDF描述 |
|---|---|
| PCA9554TS,118 | IC I/O EXPANDER I2C 8B 20SSOP |
| PCA9554ATS,118 | IC I/O EXPANDER I2C 8B 20SSOP |
| PCA9507D,112 | IC I/O EXPANDER I2C 24B 8SOIC |
| PCA9554ABS3,118 | IC I/O EXPANDER I2C 8B 16HVQFN |
| PCA9554BS3,118 | IC I/O EXPANDER I2C 8B 16HVQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCA9538PWG4 | 功能描述:接口-I/O扩展器 Rem 8B I2C & SMBus Lo-Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| PCA9538PWR | 功能描述:接口-I/O扩展器 Rem 8B I2C & SMBus Lo-Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| PCA9538PWR | 制造商:Texas Instruments 功能描述:IC I/O EXPANDER 8BIT 400KHZ TSSOP-16 |
| PCA9538PWRG4 | 功能描述:接口-I/O扩展器 Rem 8B I2C & SMBus Lo-Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| PCA9538RGTR | 制造商:TI 制造商全称:Texas Instruments 功能描述:REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS |
发布紧急采购，3分钟左右您将得到回复。