- 您现在的位置：买卖IC网 > PDF目录369949 > PCA9553DP01 (NXP Semiconductors N.V.) 4-bit I2C LED driver with programmable blink rates PDF资料下载
参数资料
| 型号： | PCA9553DP01 |
| 厂商： | NXP Semiconductors N.V. |
| 元件分类： | LED驱动器 |
| 英文描述： | 4-bit I2C LED driver with programmable blink rates |
| 中文描述： | 4位I2C LED与可编程闪烁率司机 |
| 文件页数： | 5/18页 |
| 文件大小： | 130K |
| 代理商： | PCA9553DP01 |
Philips Semiconductors
Product data sheet
PCA9553
4-bit I
2
C LED driver with programmable blink rates
2004 Oct 01
5
PWM1 — PWM REGISTER 1
bit
7
default
1
The PWM1 register determines the duty cycle of BLINK1. The
outputs are LOW (LED off) when the count is less than the value in
PWM1 and HIGH when it is greater. If PWM1 is programmed with
00h, then the PWM1 output is always LOW.
The duty cycle of BLINK1 is: 256 256
6
0
5
0
4
0
3
0
2
0
1
0
0
0
LS0 — LED SELECTOR
LED3
LED2
LED 1
3
0
LED 0
1
0
bit
7
0
6
1
5
0
4
1
2
1
0
1
default
The LSx LED select registers determine the source of the LED data.
00 = Output is set LOW (LED on)
01 = Output is set Hi-Z (LED off – default)
10 = Output blinks at PWM0 rate
11 = Output blinks at PWM1 rate
PINS USED AS GENERAL PURPOSE I/Os
LED pins not used to control LEDs can be used as general purpose
I/Os.
For use as input: Set LEDx to high-impedance (01) and then read
the pin state via the input register.
For use as output: Connect external pull-up resistor to the pin and
size it according to the DC recommended operating characteristics.
LED output pin is HIGH when the output is programmed as
high-impedance, and LOW when the output is programmed LOW
through the “LED selector” register. The output can be pulse-width
controlled when PWM0 or PWM1 are used.
POWER-ON RESET
When power is applied to V
DD
, an internal Power-On Reset holds
the PCA9553 in a reset condition until V
DD
has reached V
POR
. At
this point, the reset condition is released and the PCA9553 registers
are initialized to their default states, with all outputs in the off state.
Thereafter, V
DD
must be lowered below 0.2 V to reset the device.
相关PDF资料 |
PDF描述 |
|---|---|
| PCA9553DP02 | 4-bit I2C LED driver with programmable blink rates |
| PCA9561 | Quad 6-bit multiplexed I2C EEPROM DIP switch |
| PCB2421 | 1K dual mode serial EEPROM |
| PCB2421P | 1K dual mode serial EEPROM |
| PCB2421T | 1K dual mode serial EEPROM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCA9553DP02 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:4-bit I2C LED driver with programmable blink rates |
| PCA9553TK | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:4-bit I2C-bus LED driver with programmable blink rates |
| PCA9553TK,118 | 功能描述:LED照明驱动器 4BIT I2C FM OD LED RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| PCA9553TK/02 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:4-bit I2C-bus LED driver with programmable blink rates |
| PCA9553TK/02,118 | 功能描述:LED照明驱动器 LED DRVR 4Segment 2.5V/3.3V/5V 8-Pin RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。