参数资料
| 型号： | PCA9557PW,112 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 2/30页 |
| 文件大小： | 0K |
| 描述： | IC I/O EXPANDER I2C 8B 16TSSOP |
| 标准包装： | 96 |
| 接口： | I²C，SM 总线 |
| 输入/输出数： | 8 |
| 中断输出： | 无 |
| 频率 - 时钟： | 400kHz |
| 电源电压： | 2.3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 管件 |
| 包括： | POR |
| 产品目录页面： | 826 (CN2011-ZH PDF) |
| 其它名称： | 568-5028 935270669112 PCA9557PW PCA9557PW,112-ND PCA9557PW-ND |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
PCA9557
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 7 — 10 December 2013
10 of 30
NXP Semiconductors
PCA9557
8-bit I2C-bus and SMBus I/O port with reset
8.2 System configuration
A device generating a message is a ‘transmitter’; a device receiving is the ‘receiver’. The
device that controls the message is the ‘master’ and the devices which are controlled by
the master are the ‘slaves’ (see Figure 12).
8.3 Acknowledge
The number of data bytes transferred between the START and the STOP conditions from
transmitter to receiver is not limited. Each byte of eight bits is followed by one
acknowledge bit. The acknowledge bit is a HIGH level put on the bus by the transmitter,
whereas the master generates an extra acknowledge related clock pulse.
A slave receiver which is addressed must generate an acknowledge after the reception of
each byte. Also a master must generate an acknowledge after the reception of each byte
that has been clocked out of the slave transmitter. The device that acknowledges has to
pull down the SDA line during the acknowledge clock pulse, so that the SDA line is stable
LOW during the HIGH period of the acknowledge related clock pulse; set-up and hold
times must be taken into account.
A master receiver must signal an end of data to the transmitter by not generating an
acknowledge on the last byte that has been clocked out of the slave. In this event, the
transmitter must leave the data line HIGH to enable the master to generate a STOP
condition.
Fig 11. Definition of START and STOP conditions
mba608
SDA
SCL
P
STOP condition
S
START condition
Fig 12. System configuration
002aaa966
MASTER
TRANSMITTER/
RECEIVER
SLAVE
RECEIVER
SLAVE
TRANSMITTER/
RECEIVER
MASTER
TRANSMITTER
MASTER
TRANSMITTER/
RECEIVER
SDA
SCL
I2C-BUS
MULTIPLEXER
SLAVE
相关PDF资料 |
PDF描述 |
|---|---|
| ATMEGA48P-20MMUR | MCU AVR 4K FLASH 20MHZ 28QFN |
| ATTINY461-15MZ | MCU AVR 4K FLASH 15MHZ 32-QFN |
| MIC74YQS TR | IC I/O EXPANDER I2C 8B 16QSOP |
| MCP25050T-E/SL | IC I/O EXPANDER CAN 8B 14SOIC |
| MCP25050-E/SL | IC I/O EXPANDER CAN 8B 14SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCA9557PW112 | 制造商:NXP Semiconductors 功能描述:IC I/O EXPANDER 8BIT 400KHZ TSSOP-16 |
| PCA9557PW118 | 制造商:NXP Semiconductors 功能描述:IC I/O EXPANDER 8BIT 400KHZ TSSOP-16 |
| PCA9557PWG4 | 功能描述:接口-I/O扩展器 Rem 8B I2C & SMBus Low-Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| PCA9557PWR | 功能描述:接口-I/O扩展器 Remote 8B I2C & SMBus I/O Expander RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| PCA9557PWRG4 | 功能描述:接口-I/O扩展器 Rem 8B I2C & SMBus Low-Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。