参数资料
型号: PCA9634D,118
厂商: NXP Semiconductors
文件页数: 25/38页
文件大小: 0K
描述: IC LED DRIVER RGBA 20-SOIC
产品培训模块: LED Controllers
I²C Bus Fundamentals
标准包装: 1
拓扑: 开路漏极,PWM
输出数: 8
内部驱动器: 两者兼有
类型 - 主要: 背光,LED 闪烁器
类型 - 次要: RGBA
频率: 25MHz
电源电压: 2.3 V ~ 5.5 V
输出电压: 5.5V
安装类型: 表面贴装
封装/外壳: 20-SOIC(0.295",7.50mm 宽)
供应商设备封装: 20-SO
包装: 标准包装
工作温度: -40°C ~ 85°C
产品目录页面: 845 (CN2011-ZH PDF)
其它名称: 568-4065-6
NXP Semiconductors
PCA9634
8-bit Fm+ I 2 C-bus LED driver
Question 3: Can I really sink 400 mA through the single ground pin on the package and
will this cause any ground bounce problem due to the PWM of the LEDs?
? Yes, you can sink 400 mA through a single ground pin on the package . Although the
package only has one ground pin, there are two ground pads on the die itself
connected to this one pin. Although some ground bounce is likely, it will not disrupt the
operation of the part and would be reduced by the external decoupling capacitance.
Question 4: I can’t turn the LEDs on or off, but their registers are set properly. Why?
? Check the Mode Register 1 bit 4 SLEEP setting. The value needs to be 0 so that the
OSC is turn on. If the OSC is turned off, the LEDs cannot be turned on or off and also
can’t be dimmed or blinked.
Question 5: I’m using LEDs with integrated Zener diodes and the IC is getting very hot.
Why?
? The IC outputs can be set to either open-drain or push-pull and default to push-pull
outputs. In this application with the Zener diodes, they need to be set to open-drain
since in the push-pull architecture there is a low resistance path to ground through the
Zener and this is causing the IC to overheat. The PCA9632/33/34/35 ICs all power-up
in the push-pull output mode and with the logic state HIGH, so one of the ?rst things
that need to be done is to set the outputs to open-drain.
11. Limiting values
Table 16. Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
V DD
V I/O
I O(LEDn)
I SS
P tot
T stg
T amb
Parameter
supply voltage
voltage on an input/output pin
output current on pin LEDn
ground supply current
total power dissipation
storage temperature
ambient temperature
Conditions
operating
Min
? 0.5
V SS ? 0.5
-
-
-
? 65
? 40
Max
+6.0
5.5
25
200
400
+150
+85
Unit
V
V
mA
mA
mW
° C
° C
PCA9634_6
? NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 06 — 12 September 2008
25 of 38
相关PDF资料
PDF描述
PCA9635PW/S911,118 IC LED DRIVER RGBA 28-TSSOP
PCA9685PW,118 IC LED DRIVER RGBA 28-TSSOP
PCA9922PW,118 IC LED DRIVER LINEAR 16-TSSOP
PCA9955TW,118 IC LED DRVR CONST CURR
PCF85102C-2P/03,11 IC EEPROM 2KBIT 100KHZ 8DIP
相关代理商/技术参数
参数描述
PCA9634D-T 功能描述:LED照明驱动器 8BIT I2C FM+ TP LED CON RST OE RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9634PW 功能描述:LED照明驱动器 8BIT I2C FM+ TP LED CON RST OE RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9634PW,112 功能描述:LED照明驱动器 8BIT I2C FM+ TP LED RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9634PW,118 功能描述:LED照明驱动器 8BIT I2C FM+ TP LED CON RST OE RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9634PW,118-CUT TAPE 制造商:NXP 功能描述:PCA9634 Series 5.5 V 400 kHz SMT 8 bit Fm+I2C Bus LED Driver - TSSOP-20