参数资料
| 型号： | PCA9672PW,118 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 5/36页 |
| 文件大小： | 0K |
| 描述： | IC I/O EXPANDER I2C 8B 16TSSOP |
| 标准包装： | 2,500 |
| 接口： | I²C |
| 输入/输出数： | 8 |
| 中断输出： | 是 |
| 频率 - 时钟： | 1MHz |
| 电源电压： | 2.3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 带卷 (TR) |
| 包括： | POR |
| 其它名称： | 935282747118 PCA9672PW-T PCA9672PW-T-ND |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
PCA9672
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 3 — 27 May 2013
13 of 36
NXP Semiconductors
PCA9672
Remote 8-bit I/O expander for Fm+ I2C-bus with interrupt and reset
8.5 Interrupt output (INT)
The PCA9672 provides an open-drain output (INT) which can be fed to a corresponding
input of the microcontroller (see Figure 15). As soon as a port input is changed, the INT
will be active (LOW) and notify the microcontroller.
An interrupt is generated at any rising or falling edge of the port inputs. After time tv(Q), the
signal INT is valid.
The interrupt will reset to HIGH when data on the port is changed to the original setting or
data is read or written by the master.
In the Write mode, the interrupt may be reset (HIGH) on the rising edge of the
acknowledge bit of the data byte and also on the rising edge of the write to port pulse. The
interrupt will always be reset (HIGH) on the falling edge of the write to port pulse (see
The interrupt is reset (HIGH) in the rising edge of the read from port pulse (see Figure 14).
During the interrupt reset, any I/O change close to the read or write pulse may not
generate an interrupt, or the interrupt will have a very short pulse. After the interrupt is
reset, any change in I/Os will be detected and transmitted as an INT.
At power-on reset all ports are in Input mode and the initial state of the ports is HIGH,
therefore, for any port pin that is pulled LOW or driven LOW by external source, the
interrupt output will be active (output LOW).
8.6 RESET input
A reset can be accomplished by holding the RESET pin LOW for a minimum of tw(rst). The
PCA9672 registers and I2C-bus state machine will be held in their default state until the
RESET input is once again HIGH. The RESET input pin requires a pull-up resistor to VDD
if no active connection is used.
Fig 15. Application of multiple PCA9672s with interrupt
002aac328
VDD
MICROCOMPUTER
INT
PCA9672
INT
PCA9672
INT
device 1
device 2
PCA9672
INT
device 8
相关PDF资料 |
PDF描述 |
|---|---|
| PCA9673DB,112 | IC I/O EXPANDER I2C 16B 24SSOP |
| PCA9674PW/S911,118 | IC I/O EXPANDER I2C 8B 16TSSOP |
| PCA9675PW/S911,118 | IC I/O EXPANDER I2C 16B 24TSSOP |
| PCA9698DGG/S911,51 | IC I/O EXPANDER I2C 40B 56TSSOP |
| PCF51AC256BCPUE | MCU 8BIT 256K FLASH 64-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCA9673BQ,118 | 功能描述:接口-I/O扩展器 REMOTE 16BIT GPIO RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| PCA9673BQ-T | 功能描述:接口-I/O扩展器 REMOTE 16BIT GPIO FM+I2C-RESET RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| PCA9673BS,118 | 功能描述:接口-I/O扩展器 REMOTE 16BIT GPIO RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| PCA9673BS-T | 功能描述:接口-I/O扩展器 REMOTE 16BIT GPIO FM+I2C-RESET RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| PCA9673D | 功能描述:接口-I/O扩展器 16BIT I2C FM+ QBGPIO INT-RS PU RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。