- 您现在的位置：买卖IC网 > PDF目录16039 > PCM17XA0 (Microchip Technology)PROCESSOR MODULE 17C4X,75X,76X PDF资料下载
参数资料
| 型号： | PCM17XA0 |
| 厂商： | Microchip Technology |
| 文件页数： | 4/18页 |
| 文件大小： | 0K |
| 描述： | PROCESSOR MODULE 17C4X,75X,76X |
| 标准包装： | 3 |
| 模块/板类型： | 处理器模块 |
| 适用于相关产品： | ICE2000 |
| 配用： | ICE2000-ND - EMULATOR MPLAB-ICE 2000 POD |
| 相关产品： | DVA17XP401-ND - DEVICE ADAPTER FOR PIC17C42A DVA17XL841-ND - DEVICE ADAPTER FOR PIC17C762 DVA17XL681-ND - DEVICE ADAPTER FOR PIC17C752 DVA17XL441-ND - DEVICE ADAPTER FOR PIC17C42A DVA17PQ801-ND - DEVICE ADAPTER FOR PIC17C762 DVA17PQ641-ND - DEVICE ADAPTER FOR PIC17C752 DVA17PQ441-ND - DEVICE ADAPTER FOR PIC17C42A |
MPLAB ? ICE 2000
4.3.2
CLOCK SOURCE FROM THE TARGET
4.5
Freeze Mode
APPLICATION
If the target application is selected to provide the clock
source, the target board must also be selected to
power the emulator processor (see the MPLAB ICE
2000 on-line help file in MPLAB IDE ( Help>Topics ) or
the “ MPLAB ? ICE 2000 In-Circuit Emulator User ’s
Guide” (DS51488), “Using a Target Board Clock”).
At low voltage, the maximum speed of the processor
will be limited to the rated speed of the device under
emulation.
An oscillator circuit on the device adapter generates a
clock to the processor module and buffers the clock
circuit on the target board. In this way, the MPLAB ICE
2000 emulator closely matches the oscillator options of
the actual device. All oscillator modes are supported
(as documented in the device’s data sheet) except as
noted in Section 3.0 “Emulator-Related Issues” . The
OSC1 and OSC2 inputs of the device adapter have a
5 pF to 10 pF load. Be aware of this when using a
crystal in HS, XT, LP or LF modes, or an RC network in
RC mode.
The frequency of the emulated RC network may vary
relative to the actual device due to emulator circuitry.
If a specific frequency is important, adjust the RC val-
ues to achieve the desired frequency. Another alterna-
tive would be to allow the emulator to provide the
When using the target board clock, the system’s
operating voltage is between 2.5V and 5.5V.
The MPLAB ICE 2000 system allows the option of
“freezing” peripheral operation or allowing them to
continue operating when the processor is halted. This
option is configured in the MPLAB IDE. The Freeze
function is available on all processor modules except
the PCM16XA0.
This function is useful to halt an on-board timer while at
a break point. At a break point and while single
stepping, interrupts are disabled.
5.0 DEVICE ADAPTER ISSUES
This section details processor-specific considerations
that have been made on device adapters. Only
adapters with special considerations are listed.
There will be a max of 10 mA of current draw from the
target system even when the emulator processor
module is being powered by the emulator system, and
running internal clock. This is due to components on
the device adapter being powered by the target board.
4.4
ESD Protection and Electrical
Overstress
All CMOS chips are susceptible to electrostatic
discharge (ESD). In the case of the processor modules,
the pins of the CMOS emulator are directly connected
to the target connector, making the chip vulnerable to
ESD. ESD can also induce latch-up in CMOS chips,
causing excessive current through the chip and
possible damage. MPLAB ICE 2000 has been
designed to minimize potential damage by implement-
ing overcurrent protection and transient suppressors.
However, care should be given to minimizing ESD
conditions while using the system.
During development, contention on an I/O pin is
possible (e.g., when an emulator pin is driving a ‘ 1 ’ and
the target board is driving a ‘ 0 ’). Prolonged contention
may cause latch-up and damage to the emulator chip.
One possible precaution is to use current limiting
resistors (~100 Ω ) during the development phase on
bidirectional I/O pins. Using limiting resistors can also
help avoid damage to modules, device adapters and
pods that occurs when a voltage source is accidentally
connected to an I/O pin on the target board.
DS51140M-page 4
? 2006 Microchip Technology Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-JVV-EY-S | CONVERTER MOD DC/DC 5.8V 50W |
| VE-JVT-EZ-F4 | CONVERTER MOD DC/DC 6.5V 25W |
| AC164024 | ADAPTER PICSTART PLUS 68PLCC |
| RCM22DCWT | CONN EDGECARD 44POS DIP .156 SLD |
| RBM22DCSS | CONN EDGECARD 44POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCM-18 | 功能描述:电线鉴定 1.5" VINYL CLOTH #18 RoHS:否 制造商:TE Connectivity / Q-Cees 产品:Labels and Signs 类型: 材料:Vinyl 颜色:Blue 宽度:0.625 in 长度:1 in |
| PCM-1-8 | 制造商:Panduit Corp 功能描述:Cable Markers Vinyl White 制造商:Panduit Corp 功能描述:CBL ACC MARKER CARD VINYL BLK/WHITE - Labels that come on sheets or rolls |
| PCM-180 | 功能描述:电线鉴定 1.5 VINYL CLOTH #180 RoHS:否 制造商:TE Connectivity / Q-Cees 产品:Labels and Signs 类型: 材料:Vinyl 颜色:Blue 宽度:0.625 in 长度:1 in |
| PCM-1800-1824 | 制造商:Panduit Corp 功能描述:Call vendor for pricing |
| PCM1800E | 功能描述:音频模/数转换器 IC Sngl-End Analog Inp 20-Bit Stereo ADC RoHS:否 制造商:Wolfson Microelectronics 转换速率: 分辨率: ADC 输入端数量: 工作电源电压: 最大工作温度: 最小工作温度: 安装风格: 封装 / 箱体: 封装: |
发布紧急采购，3分钟左右您将得到回复。