- 您现在的位置：买卖IC网 > PDF目录21897 > PE43702MLI-Z (Peregrine Semiconductor)IC RF DSA 7BIT 50 OHM 24-QFN PDF资料下载
参数资料
| 型号： | PE43702MLI-Z |
| 厂商： | Peregrine Semiconductor |
| 文件页数： | 8/11页 |
| 文件大小： | 0K |
| 描述： | IC RF DSA 7BIT 50 OHM 24-QFN |
| 标准包装： | 1 |
| 系列： | UltraCMOS™, HaRP™ |
| 衰减值： | 31.75dB |
| 容差： | ±0.3dB |
| 频率范围： | 9kHz ~ 4GHz |
| 阻抗： | 50 欧姆 |
| 封装/外壳： | 24-VFQFN 裸露焊盘 |
| 其它名称： | 1046-1047-6 |
PE43702
Product Specification
Evaluation Kit
The Digital Attenuator Evaluation Kit board was
designed to ease customer evaluation of the
PE43702 Digital Step Attenuator.
Direct-Parallel Programming Procedure
For automated direct-parallel programming,
connect the test harness provided with the EVK
from the parallel port of the PC to the J1 & Serial
header pin and set the D0-D6 SP3T switches to
the ‘MIDDLE’ toggle position. Position the
Parallel/Serial ( P / ? S) select switch to the Parallel
(or left) position. The evaluation software is
written to operate the DSA in either Parallel or
Serial-Addressable Mode. Ensure that the
software is set to program in Direct-Parallel mode.
Using the software, enable or disable each setting
to the desired attenuation state. The software
automatically programs the DSA each time an
attenuation state is enabled or disabled.
For manual direct-parallel programming,
disconnect the test harness provided with the EVK
from the J1 and Serial header pins. Position the
Parallel/Serial ( P / ? S) select switch to the Parallel
(or left) position. The LE pin on the Serial header
must be tied to V DD . Switches D0-D6 are SP3T
switches which enable the user to manually
program the parallel bits. When any input D0-D6
is toggled ‘UP’, logic high is presented to the
parallel input. When toggled ‘DOWN’, logic low is
presented to the parallel input. Setting D0-D6 to
the ‘MIDDLE’ toggle position presents an OPEN,
which forces an on-chip logic low. Table 9 depicts
the parallel programming truth table and Fig. 16
illustrates the parallel programming timing
Figure 17. Evaluation Board Layout
Peregrine Specification 101-0310
Note: Reference Figure 18 for Evaluation Board Schematic
as the parallel bits are applied. The user must
then pulse LE from 0V to V DD and back to 0V to
latch the programming word into the DSA. LE
must be logic low prior to programming the next
word.
diagram.
Serial Programming Procedure
Latched-Parallel Programming Procedure
For automated latched-parallel programming, the
procedure is identical to the direct-parallel
method. The user only must ensure that Latched-
Parallel is selected in the software.
For manual latched-parallel programming, the
procedure is identical to direct-parallel except now
the LE pin on the Serial header must be logic low
Position the Parallel/Serial ( P / ? S) select switch to
the Serial (or right) position. The evaluation
software is written to operate the DSA in either
Parallel or Serial Mode. Ensure that the software
is set to program in Serial mode. Using the
software, enable or disable each setting to the
desired attenuation state. The software
automatically programs the DSA each time an
attenuation state is enabled or disabled.
?2008-2009 Peregrine Semiconductor Corp. All rights reserved.
Document No. 70-0244-04
│ UltraCMOS? RFIC Solutions
Page 8 of 11
Logo updated under non-rev change. Peregrine products are protected under one or more of the following U.S. Patents: http://patents.psemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| PE43602MLI-Z | IC RF DSA 6BIT 50 OHM 24-QFN |
| DCA-20PC-4-DC4-RL-C | AMMETER LED 8-36VDC 199.9MA RED |
| PE43502MLI-Z | IC RF DSA 5-BIT 50 OHM 24-QFN |
| PE43701MLI-Z | IC RF DSA 7BIT 50 OHM 32QFN |
| 4306-52 | IC DSA 5BIT 50 OHM 20-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PE43703MLI | 制造商:Peregrine Semiconductor 功能描述:ATTENUATOR - DIGITALLY CONTROLLED 制造商:Peregrine Semiconductor 功能描述:Digital Attenuator 31.75dB Attenuation 4GHz/5GHz/6GHz 32-Pin QFN EP Bulk |
| PE43703MLI-Z | 功能描述:IC RF DSA 7BIT 50 OHM 32-QFN RoHS:是 类别:RF/IF 和 RFID >> 衰减器 系列:UltraCMOS™, HaRP™ 标准包装:1 系列:- 衰减值:- 容差:±1% 频率范围:0 ~ 500MHz 功率（瓦特）:2W 阻抗:93 欧姆 封装/外壳:BNC 单排模块 |
| PE43704DS | 制造商:PSEMI 制造商全称:PSEMI 功能描述:UltraCMOS?? RF Digital Step Attenuator, 7-bit, 31.75 dB with Optional VssEXT Bypass Mode 9 kHz - 8 GHz |
| PE43704MLCA-Z | 制造商:Peregrine Semiconductor 功能描述:ATTENUATOR - DIGITALLY CONTROLLED |
| PE43705A-Z | 功能描述:RF Attenuator 31.75dB 50MHz ~ 8GHz 50 Ohm 32-VFQFN Exposed Pad 制造商:peregrine semiconductor 系列:UltraCMOS?，HaRP?? 零件状态:有效 衰减值:31.75dB 容差:- 频率范围:50MHz ~ 8GHz 功率（W）:- 阻抗:50 欧姆 封装/外壳:32-VFQFN 裸露焊盘 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。