- 您现在的位置：买卖IC网 > PDF目录16692 > PI2007D3-EVAL1 (Vicor Corporation)EVAL BRD FOR PI2007/PI2003 DUAL PDF资料下载
参数资料
| 型号： | PI2007D3-EVAL1 |
| 厂商： | Vicor Corporation |
| 文件页数： | 10/16页 |
| 文件大小： | 0K |
| 描述： | EVAL BRD FOR PI2007/PI2003 DUAL |
| 产品培训模块： | Cool-ORing? Series |
| 标准包装： | 1 |
| 系列： | Picor®, Cool-ORing® |
| 主要目的： | 电源管理，O 环控制器/负荷分载 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | PI2003，PI2007 |
| 已供物品： | 板 |
| 其它名称： | 1102-1056 |
Application Information:
Pd Rbias =
The PI2003 is designed to replace ORing diodes in
high current redundant power architectures.
Replacing a traditional diode with a PI2003
controller IC and a low on-state resistance N-
channel MOSFET will result in significant power
dissipation reduction as well as board space
reduction, efficiency improvement and additional
protection features. This section describes in detail
the procedure to follow when designing with the
PI2003 Active ORing controller and N-Channel
MOSFETs. The following is a low side Active ORing
design example.
Fault Indication:
FT output pin is an open collector output and
should be pulled up to the logic voltage or to the
controller VC via a resistor (10K ? ). Also the FT
output can be pulled with a current limiting resistor
directly to an unregulated voltage source, such as
the return of a -48V bus. In this condition connect
the FT pin to the FC pin for clamping.
Also the FT pin can be used to drive an LED or
opto-coupler device. The circuit in figure 12a shows
a PI2003 configuration for an LED/opto-coupler that
will turn on during a fault condition. The FC
connection protects the FT pin if the LED is open.
Use the circuit in figure 12b to turn on the LED/opto-
coupler when there is no fault and to turn off during
a fault condition.
enhance the MOSFET. The maximum gate to VC
voltage loss (headroom), VHD VC-G is 0.5V.
VHD VC-G specification is the Gate Voltage High (V G )
in the Gate Driver section under the
Electrical Specification.
If the bus voltage is higher than 11V then a bias
resistor (Rbias) is required, and should be
connected between the PI2003 VC pin and supply.
The resistor is selected based on the input voltage
range.
Vbus min ? VC clamp
Rbias =
IC max
Rbias maximum power dissipation:
( Vbus max ? VC clamp ) 2
Rbias
Rbias maximum power dissipation is at maximum
input voltage and minimum clamp voltage (11V).
Where:
Vbus min : V(bus) minimum voltage
Vbus max : V(bus) maximum voltage
VC Clamp : Controller clamp voltage, 11V
IC max : Controller maximum bias current (2.0mA)
Note: If the FT pin is connected to the VC pin via a
resistor (R FT ), the FT sink current ( I FT )
during a fault condition should be added to
the maximum bias current
IC max in the
above equations.
The FT pin sink current during a fault can
be calculated using the following
approximate equation:
Figure 12a: Fault circuit where the LED turns on
during a fault.
I FT =
VC clampMax
R FT
N-Channel MOSFET Selection:
There are several factors that affect the MOSFET
selection including cost, on-state resistance
(Rds(on)), current rating, power dissipation, thermal
conductivity, drain-to-source breakdown voltage
(BVdss), gate-to-source voltage rating (Vgs), and
gate threshold voltage (Vgs (TH) ).
Figure 12b: Fault circuit where the LED turns off
during a fault.
VC Power Source:
The PI2003 VC input voltage should be higher than
the required gate-to-source voltage (Vgs) to fully
The first step is to select suitable MOSFETs based
on the BVdss requirement for the application. The
BVdss voltage rating should be higher than the
applied Vin voltage plus expected transient voltages.
Stray parasitic inductance in the circuit can also
contribute to significant transient voltage conditions,
particularly during MOSFET turn-off after a reverse
Picor Corporation ? picorpower.com
PI2003
Rev 1.1
Page 10 of 16
相关PDF资料 |
PDF描述 |
|---|---|
| 4922R-27L | INDUCTOR 150UH POWER SMD |
| AFK107M25E16T-F | CAP ALUM 100UF 25V 20% SMD |
| V72C24E150BG | CONVERTER MOD DC/DC 24V 150W |
| RBA14DRMD-S288 | CONN EDGECARD 28POS .125 EXTEND |
| V375C48T75BG2 | CONVERTER MOD DC/DC 48V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PI2007-EVAL1 | 功能描述:EVAL BRD FOR PI2007 48V/6A RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:Picor®, Cool-ORing® 标准包装:1 系列:- 主要目的:数字电位器 嵌入式:- 已用 IC / 零件:AD5258 主要属性:- 次要属性:- 已供物品:板 相关产品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP |
| PI2007-EVAL2 | 功能描述:EVAL BRD FOR PI2007 12V/15A RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:Picor®, Cool-ORing® 标准包装:1 系列:- 主要目的:数字电位器 嵌入式:- 已用 IC / 零件:AD5258 主要属性:- 次要属性:- 已供物品:板 相关产品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP |
| PI200MC-A4 | 制造商:AMI 制造商全称:AMI 功能描述:200DPI CIS Module |
| PI201M-A4 | 制造商:AMI 制造商全称:AMI 功能描述:200DPI CIS Sensor |
| PI20-5,08 | 功能描述:可插拔接线端子 PCB Hdr, 45 Deg, 5,08 PitchOpen End, 20pole, 12A,300V,Grn RoHS:否 制造商:Phoenix Contact 产品:Plugs 系列:PTS 端接类型:Spring Cage 位置/触点数量:5 线规量程:26-14 节距:5 mm 电流额定值:10 A 电压额定值:250 V 安装风格: 安装角: 触点电镀: |
发布紧急采购，3分钟左右您将得到回复。