参数资料
型号: PI3HDMI411AD
厂商: Pericom Semiconductor Corp.
英文描述: DVI / HDMI Re-Driver w/ Equalization, De-emphasis & Pre-emphasis
中文描述: HDMI / DVI数字重新驱动瓦特/均等,去加重
文件页数: 2/9页
文件大小: 487K
代理商: PI3HDMI411AD
2
PS8845G 01/18/07
PI3HDMI411AD
DVI / HDMI Re-Driver
w/ Equalization, De-emphasis & Pre-emphasis
Storage Temperature.....................................–65°C to +150°C
Supply Voltage to Ground Potential.............–0.5V to +5V
DC Input Voltage..........................................–0.5V to V
DD
DC Output Current.......................................120mA
Power Dissipation.........................................1.0W
Note:
Stresses greater than those listed under MAX MUM RAT NGS may cause
permanent damage to the de vice. This is a stress rating only and func-
ion al op er a ion of the device at these or any other conditions above those
indicated in the operational sections of this spec
fi
ca ion is not implied.
Exposure to absolute max mum rating con di ions for extended periods
may affect re i abil y.
Maximum Ratings
(Above which useful life may be impaired. For user guide ines,
not tested.)
Pin Description
Pin #
2, 6, 11, 15, 22, 24, 36, 48
3, 14, 21, 23, 27, 30, 33, 39,
42, 45, 53
19
20
1
DD
V
S
D
v
c
E
w
M
e
T
R
r
Q
TMDS
Driver
Dx+I
Dx-I
Dx+O
Dx-O
50Ω
50Ω
Function Block Description
Notes:
1. X = 0,1,2,3
Pin Name
V
DD
GND
I/O
Power 3.3V power supply
Power 0V power supply
Description
SCL
SDA
MS
I
I2C Clock Input Signal, if and only if MS = 'HIGH'
I2C Data Input/Output Signal, if and only if MS = 'HIGH'
Mode Select Pin. If MS = ‘HIGH’, then I2C control is active. Pins 49-52
are I2C address and pin 19 is SCL and pin 20 is SDA. If MS = ‘LOW’, then
I2C control is inactive and pin programmability is active.
I/O
I
56
OE
I
Output is enabled and normal when OE = ‘HIGH’. If OE = ‘LOW’, both
outputs, A and B, are disabled and at Hi-Z
Input TMDS high speed signals
4, 5 ,7, 8 ,9 ,10, 12, 13
DxI,
CLKI
DxO,
CLKO
A0, A1,
A2, A3
S4, S5, S6,
S7
S3
I
37, 38, 40, 41, 43, 44, 46, 47
O
Output TMDS high speed signals
49, 50, 51, 52
I
I2C address inputs if MS = ‘HIGH’.
49, 50, 51, 52
I
If MS = ‘LOW’, then pins 49-52 are control bits S4-S7 for output port only,
as shown in truth table on page 3 of datasheet
If MS = ‘LOW’, then pins 19 is control bit S3, as shown in the truth table on
page 3
If MS = ‘LOW’, then pins 20 is control bit S2, as shown in the truth table on
page 3
No Connect
19
I
20
S2
I
16, 17, 18, 25, 26, 28, 29, 31,
32, 34, 35, 54, 55
NC
N/A
07-0017
相关PDF资料
PDF描述
PI3HDMI412FT 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch with Flow-through Pin Out
PI3HDMI412FTBE 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch with Flow-through Pin Out
PI3HDMI412FTZHE 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch with Flow-through Pin Out
PI3HDMI414 4-Differential Channel, 4:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch
PI3HDMI414BE 4-Differential Channel, 4:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch
相关代理商/技术参数
参数描述
PI3HDMI411ADEVB 制造商:Pericom Semiconductor Corporation 功能描述:
PI3HDMI411ADZBE 功能描述:数字总线开关 IC HDMI 1:1re-driver 3.3V RoHS:否 制造商:Texas Instruments 开关数量:24 传播延迟时间:0.25 ns 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:TSSOP-56 封装:Reel
PI3HDMI411ADZBEX 功能描述:特殊用途放大器 HDMI Redriver RoHS:否 制造商:Texas Instruments 通道数量:Single 共模抑制比(最小值): 输入补偿电压: 工作电源电压:3 V to 5.5 V 电源电流:5 mA 最大功率耗散: 最大工作温度:+ 70 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-20 封装:Reel
PI3HDMI412-A 制造商:PERICOM 制造商全称:Pericom Semiconductor Corporation 功能描述:4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard
PI3HDMI412-ABE 功能描述:多路器开关 IC DVI/HDMI Passive Switch RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻(最大值):7 Ohms 开启时间(最大值): 关闭时间(最大值): 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16