2
PS8144C 01/11/01
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
PI5C3306
2-Bit Bus Switch with Active Low Enables
Capacitance
(T
A
= 25°C, f = 1 MHz)
Parameters
(4)
C
IN
C
OFF
C
ON
Description
Input Capacitance
A/B Capacitance, Switch Off
A/B Capacitance, Switch On
Test Conditions
V
IN
= 0V
V
IN
= 0V
V
IN
= 0V
Typ
3
5
10
Units
pF
pF
pF
Parameters
V
IH
V
IL
I
IH
I
IL
I
OZH
I
OZL
V
H
R
ON
Description
Test Conditions
(1)
Min.
2.0
–0.5
Typ
(2)
Max.
Units
V
V
μA
Input HIGH Voltage
Input LOW Voltage
Input HIGH Current
Guaranteed Logic HIGH Level
Guaranteed Logic LOW Level
V
CC
= Max., V
IN
= V
CC
V
CC
= Max., V
IN
= GND
0
≤
A, B
≤
V
CC
0
≤
A, B
≤
V
CC
0.8
±1
Input LOW Current
±1
μA
High Impedance Output Current
±1
μA
Low Impedance Output Current
±1
mA
Input Hysteresis at Control Pins
300
mV
Switch On Resistance
(3)
V
CC
= 4.5V, V
IN
= 0.0V, I
ON
= 30mA or 64mA
V
CC
= 4.5V, V
IN
= 2.4V, I
ON
= 15mA
5
10
7
15
Storage Temperature ..........................................................–65°C to +150°C
Ambient Temperature with Power Applied ..........................–40°C to +85°C
Supply Voltage to Ground Potential (Inputs & Vcc Only) ....–0.5V to +7.0V
Supply Voltage to Ground Potential (Outputs & D/O Only).–0.5V to +7.0V
DC Input Voltage ...................................................................–0.5V to +7.0V
DC Output Current ............................................................................ 120mA
Power Dissipation.................................................................................0.5W
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the
device. This is a stress rating only and functional
operation of the device at these or any other condi-
tions above those indicated in the operational sec-
tions of this specification is not implied. Exposure to
absolute maximum rating conditions for extended
periods may affect reliability.
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at V
CC
= 5.0V, T
A
= 25°C ambient and maximum loading.
3. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined
by the lower of the voltages on the two (A, B) pins.
4. This parameter is determined by device characterization but is not production tested.
Power Supply Characteristics
Parameters
Description
Test Conditions
(1)
Min.
Typ
(2)
Max.
Units
I
CC
I
CC
Quiescent Power Supply Current
V
CC
= Max.
V
CC
= Max.
V
IN
= GND or V
CC
V
IN
= 3.4V
(3)
0.1
3.0
μA
Supply Current per Input @ TTL HIGH
2.5
mA
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device.
2. Typical values are at V
CC
= 5.0V, +25°C ambient.
3. Per TTL driven input (V
IN
= 3.4V, control inputs only); A and B pins do not contribute to I
CC
.
DC Electrical Characteristics
(Over the Operating Range, T
A
= –40°C to +85°C, V
CC
= 4V to 5.5V)