参数资料
型号: PIC16C712T-04E/SO
厂商: Microchip Technology
文件页数: 27/106页
文件大小: 0K
描述: IC MCU OTP 1KX14 A/D PWM 18SOIC
标准包装: 1,100
系列: PIC® 16C
核心处理器: PIC
芯体尺寸: 8-位
速度: 4MHz
外围设备: 欠压检测/复位,POR,PWM,WDT
输入/输出数: 13
程序存储器容量: 1.75KB(1K x 14)
程序存储器类型: OTP
RAM 容量: 128 x 8
电压 - 电源 (Vcc/Vdd): 4 V ~ 5.5 V
数据转换器: A/D 4x8b
振荡器型: 外部
工作温度: -40°C ~ 125°C
封装/外壳: 18-SOIC(0.295",7.50mm 宽)
包装: 带卷 (TR)
2005 Microchip Technology Inc.
DS41106B-page 25
PIC16C712/716
PORTB pins RB3:RB1 are multiplexed with several
peripheral functions (Table 3-3). PORTB pins RB3:RB0
have Schmitt Trigger input buffers.
When enabling peripheral functions, care should be
taken in defining TRIS bits for each PORTB pin. Some
peripherals override the TRIS bit to make a pin an out-
put, while other peripherals override the TRIS bit to
make a pin an input. Since the TRIS bit override is in
effect while the peripheral is enabled, read-modify-
write instructions (BSF, BCF, XORWF) with TRISB as
destination should be avoided. The user should refer to
the corresponding peripheral section for the correct
TRIS bit settings.
Four of PORTB’s pins, RB7:RB4, have an interrupt-on-
change feature. Only pins configured as inputs can
cause this interrupt to occur (i.e., any RB7:RB4 pin
configured as an output is excluded from the interrupt-
on-change comparison). The input pins, RB7:RB4, are
compared with the old value latched on the last read of
PORTB. The “mismatch” outputs of RB7:RB4 are
OR’ed together to generate the RB Port Change
Interrupt with flag bit RBIF (INTCON<0>).
This interrupt can wake the device from Sleep. The
user, in the Interrupt Service Routine, can clear the
interrupt in the following manner:
a)
Any read or write of PORTB will end the
mismatch condition.
b)
Clear flag bit RBIF.
A mismatch condition will continue to set flag bit RBIF.
Reading PORTB will end the mismatch condition and
allow flag bit RBIF to be cleared.
The interrupt-on-change feature is recommended for
wake-up on key depression operation and operations
where PORTB is only used for the interrupt-on-change
feature. Polling of PORTB is not recommended while
using the interrupt-on-change feature.
FIGURE 3-4:
BLOCK DIAGRAM OF RB1/T1OSO/T1CKI PIN
0
1
Q
D
Q
CK
Q
D
Q
CK
Q
D
Q
CK
Q
D
Q
CK
0
1
0
1
TTL Buffer
TRISB<1>
PORTB<1>
TRISCCP<0>
DATACCP<0>
RB1/T1OSO/T1CKI
RD
Data Bus
WR
WR TRISB
T1OSCEN
RD PORTB
TMR1CS
DATACCP
TRISCCP
PORTB
T1CLKIN
ST
Buffer
P
VDD
Weak
Pull-up
RBPU(1)
T1OSCEN
T1CS
VSS
VDD
Note 1: To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (OPTION_REG<7>).
0
1
TMR1CS
相关PDF资料
PDF描述
PIC16C711T-20/SS IC MCU OTP 1KX14 A/D 20SSOP
VE-21D-CU-F1 CONVERTER MOD DC/DC 85V 200W
PIC16C711T-20E/SS IC MCU OTP 1KX14 A/D 20SSOP
PIC16C711T-20E/SO IC MCU OTP 1KX14 A/D 18SOIC
PIC16C711T-04E/SS IC MCU OTP 1KX14 A/D 20SSOP
相关代理商/技术参数
参数描述
PIC16C712T-04I/SO 功能描述:8位微控制器 -MCU 1.75KB 128RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16C712T-04I/SS 功能描述:8位微控制器 -MCU 1.75KB 128RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16C712T-20/SO 功能描述:8位微控制器 -MCU 1.75KB 128RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16C712T-20/SS 功能描述:8位微控制器 -MCU 1.75KB 128RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16C712T-20E/SO 功能描述:8位微控制器 -MCU 1.75KB 128RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT