参数资料
型号: PIC16F1826-E/MV
厂商: Microchip Technology
文件页数: 31/109页
文件大小: 0K
描述: MCU PIC 8BIT 2K FLASH 28-UQFN
标准包装: 91
系列: PIC® XLP™ mTouch™ 16F
核心处理器: PIC
芯体尺寸: 8-位
速度: 32MHz
连通性: I²C,SPI,UART/USART
外围设备: 欠压检测/复位,POR,PWM,WDT
输入/输出数: 16
程序存储器容量: 3.5KB(2K x 14)
程序存储器类型: 闪存
EEPROM 大小: 256 x 8
RAM 容量: 256 x 8
电压 - 电源 (Vcc/Vdd): 1.8 V ~ 5.5 V
数据转换器: A/D 12x10b
振荡器型: 内部
工作温度: -40°C ~ 125°C
封装/外壳: 28-UFQFN 裸露焊盘
包装: 管件
186
2570N–AVR–05/11
ATmega325/3250/645/6450
an interrupt when the transfer is complete. Note that when an external clock source is selected
the counter counts both clock edges. In this case the counter counts the number of edges, and
not the number of bits. The clock can be selected from three different sources: The USCK pin,
Timer/Counter0 Compare Match or from software.
The Two-wire clock control unit can generate an interrupt when a start condition is detected on
the Two-wire bus. It can also generate wait states by holding the clock pin low after a start con-
dition is detected, or after the counter overflows.
21.2
Functional Descriptions
21.2.1
Three-wire Mode
The USI Three-wire mode is compliant to the Serial Peripheral Interface (SPI) mode 0 and 1, but
does not have the slave select (SS) pin functionality. However, this feature can be implemented
in software if necessary. Pin names used by this mode are: DI, DO, and USCK.
Figure 21-2. Three-wire Mode Operation, Simplified Diagram
Figure 21-2 shows two USI units operating in Three-wire mode, one as Master and one as
Slave. The two Shift Registers are interconnected in such way that after eight USCK clocks, the
data in each register are interchanged. The same clock also increments the USI’s 4-bit counter.
The Counter Overflow (interrupt) Flag, or USIOIF, can therefore be used to determine when a
transfer is completed. The clock is generated by the Master device software by toggling the
USCK pin via the PORT Register or by writing a one to the USITC bit in USICR.
SLAVE
MASTER
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
DO
DI
USCK
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
DO
DI
USCK
PORTxn
相关PDF资料
PDF描述
PIC16F1826-E/ML MCU PIC 8BIT 2K FLASH 28-QFN
PIC24F04KA201T-I/SO IC PIC MCU FLASH 512KX4 20-SOIC
VI-BNL-IW-F3 CONVERTER MOD DC/DC 28V 100W
VI-BNK-IX-F3 CONVERTER MOD DC/DC 40V 75W
VI-BNK-IW-F4 CONVERTER MOD DC/DC 40V 100W
相关代理商/技术参数
参数描述
PIC16F1826-I/ML 功能描述:8位微控制器 -MCU 3.5KB Flash 256 byte 32 MHz Int. Osc RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16F1826-I/MQ 功能描述:8位微控制器 -MCU 3.5KB Flash 256 byte 32 MHz Int. Osc RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16F1826-I/MV 功能描述:8位微控制器 -MCU 3.5KB Flash 256 RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16F1826-I/P 功能描述:8位微控制器 -MCU 3.5KB Flash 256 byte 32 MHz Int. Osc RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16F1826-I/SO 功能描述:8位微控制器 -MCU 3.5KB Flash 256 byte 32 MHz Int. Osc RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT