参数资料
型号: PIC16F84A-04E/SO
厂商: Microchip Technology
文件页数: 29/81页
文件大小: 0K
描述: IC MCU CMOS 4MHZ 1K FLASH 18SOIC
标准包装: 42
系列: PIC® 16F
核心处理器: PIC
芯体尺寸: 8-位
速度: 4MHz
外围设备: POR,WDT
输入/输出数: 13
程序存储器容量: 1.75KB(1K x 14)
程序存储器类型: 闪存
EEPROM 大小: 64 x 8
RAM 容量: 68 x 8
电压 - 电源 (Vcc/Vdd): 4 V ~ 5.5 V
振荡器型: 外部
工作温度: -40°C ~ 125°C
封装/外壳: 18-SOIC(0.295",7.50mm 宽)
包装: 管件
配用: I3-DB16F84A-ND - BOARD DAUGHTER ICEPIC3
2001 Microchip Technology Inc.
DS35007B-page 33
PIC16F84A
6.11.3
WAKE-UP USING INTERRUPTS
When global interrupts are disabled (GIE cleared) and
any interrupt source has both its interrupt enable bit
and interrupt flag bit set, one of the following will occur:
If the interrupt occurs before the execution of a
SLEEP
instruction, the SLEEP instruction will com-
plete as a NOP. Therefore, the WDT and WDT
postscaler will not be cleared, the TO bit will not
be set and PD bits will not be cleared.
If the interrupt occurs during or after the execu-
tion of a SLEEP instruction, the device will imme-
diately wake-up from SLEEP. The SLEEP
instruction will be completely executed before the
wake-up. Therefore, the WDT and WDT
postscaler will be cleared, the TO bit will be set
and the PD bit will be cleared.
Even if the flag bits were checked before executing a
SLEEP
instruction, it may be possible for flag bits to
become set before the SLEEP instruction completes. To
determine whether a SLEEP instruction executed, test
the PD bit. If the PD bit is set, the SLEEP instruction
was executed as a NOP.
To ensure that the WDT is cleared, a CLRWDT instruc-
tion should be executed before a SLEEP instruction.
6.12
Program Verification/Code
Protection
If the code protection bit(s) have not been pro-
grammed, the on-chip program memory can be read
out for verification purposes.
6.13
ID Locations
Four memory locations (2000h - 2004h) are designated
as ID locations to store checksum or other code
identification
numbers.
These
locations
are
not
accessible during normal execution but are readable
and writable only during program/verify. Only the
four Least Significant bits of ID location are usable.
6.14
In-Circuit Serial Programming
PIC16F84A
microcontrollers
can
be
serially
programmed while in the end application circuit. This is
simply done with two lines for clock and data, and three
other lines for power, ground, and the programming
voltage. Customers can manufacture boards with
unprogrammed
devices,
and
then
program
the
microcontroller just before shipping the product,
allowing the most recent firmware or custom firmware
to be programmed.
For complete details of Serial Programming, please
refer to the In-Circuit Serial Programming (ICSP)
Guide, (DS30277).
相关PDF资料
PDF描述
PIC16F785-I/SS IC PIC MCU FLASH 2KX14 20SSOP
PIC16C433T-I/SO IC MCU CMOS 8BIT 10MHZ 2K 18SOIC
PIC16C773T-E/SO IC MCU OTP 4KX14 A/D PWM 28SOIC
PIC16CE623T-30/SO IC MCU OTP 512X14 EE COMP 18SOIC
PIC16F1825-E/ML MCU PIC 14K FLASH 1K RAM 16QFN
相关代理商/技术参数
参数描述
PIC16F84A-04I/P 功能描述:8位微控制器 -MCU 1.75KB 68 RAM 13 I/O 4MHz Ind Temp PDIP18 RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16F84A-04I/P 制造商:Microchip Technology Inc 功能描述:IC 8BIT FLASH MCU 16F84 DIP18
PIC16F84A-04I/SO 功能描述:8位微控制器 -MCU 1.75KB 68 RAM 13 I/O 4MHz Ind Temp SOIC18 RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16F84A-04I/SO 制造商:Microchip Technology Inc 功能描述:8BIT FLASH MCU SMD 16F84 SOIC18
PIC16F84A-04I/SS 功能描述:8位微控制器 -MCU 1.75KB 68 RAM 13 I/O 4MHz IndTemp SSOP20 RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT