- 您现在的位置：买卖IC网 > PDF目录11560 > PIC16LC620AT-04/SS (Microchip Technology)IC MCU OTP 512X14 COMP 20SSOP PDF资料下载
参数资料
| 型号： | PIC16LC620AT-04/SS |
| 厂商： | Microchip Technology |
| 文件页数： | 19/89页 |
| 文件大小： | 0K |
| 描述： | IC MCU OTP 512X14 COMP 20SSOP |
| 产品培训模块： | Asynchronous Stimulus |
| 标准包装： | 1,600 |
| 系列： | PIC® 16C |
| 核心处理器： | PIC |
| 芯体尺寸： | 8-位 |
| 速度： | 4MHz |
| 外围设备： | 欠压检测/复位，POR，WDT |
| 输入/输出数： | 13 |
| 程序存储器容量： | 896B（512 x 14） |
| 程序存储器类型： | OTP |
| RAM 容量： | 96 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.5 V ~ 5.5 V |
| 振荡器型： | 外部 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 包装： | 带卷 (TR) |
| 其它名称： | PIC16LC620AT-04SS |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页
26
AT90S1200
0838H–AVR–03/02
Bit 1 – EEWE: EEPROM Write Enable
The EEPROM Write Enable Signal (EEWE) is the write strobe to the EEPROM. When
address and data are correctly set up, the EEWE bit must be set to write the value into
the EEPROM. When the write access time (typically 2.5 ms at V
CC = 5V and 4 ms at
V
CC = 2.7V) has elapsed, the EEWE bit is cleared (zero) by hardware. The user soft-
ware can poll this bit and wait for a zero before writing the next byte. When EEWE has
been set, the CPU is halted for two cycles before the next instruction is executed.
Bit 0 – EERE: EEPROM Read Enable
The EEPROM Read Enable Signal (EERE) is the read strobe to the EEPROM. When
the correct address is set up in the EEAR register, the EERE bit must be set. When the
EERE bit is cleared (zero) by hardware, requested data is found in the EEDR register.
The EEPROM read access takes one instruction and there is no need to poll the EERE
bit. When EERE has been set, the CPU is halted for four cycles before the next instruc-
tion is executed.
Caution: If an interrupt routine accessing the EEPROM is interrupting another EEPROM
access, the EEAR or EEDR register will be modified, causing the interrupted EEPROM
access to fail. It is recommended to have the global interrupt flag cleared during
EEPROM write operation to avoid these problems.
Prevent EEPROM
Corruption
During periods of low V
CC, the EEPROM data can be corrupted because the supply volt-
age is too low for the CPU and the EEPROM to operate properly. These issues are the
same as for board-level systems using the EEPROM, and the same design solutions
should be applied.
An EEPROM data corruption can be caused by two situations when the voltage is too
low. First, a regular write sequence to the EEPROM requires a minimum voltage to
operate correctly. Secondly, the CPU itself can execute instructions incorrectly, if the
supply voltage for executing instructions is too low.
EEPROM data corruption can easily be avoided by following these design recommen-
dations (one is sufficient):
1.
Keep the AVR RESET active (low) during periods of insufficient power supply
voltage. This is best done by an external low V
CC Reset Protection circuit, often
referred to as a Brown-out Detector (BOD). Please refer to application note AVR
180 for design considerations regarding power-on reset and low-voltage
detection.
2.
Keep the AVR core in Power-down Sleep mode during periods of low V
CC. This
will prevent the CPU from attempting to decode and execute instructions, effec-
tively protecting the EEPROM registers from unintentional writes.
3.
Store constants in Flash memory if the ability to change memory contents from
software is not required. Flash memory cannot be updated by the CPU, and will
not be subject to corruption.
相关PDF资料 |
PDF描述 |
|---|---|
| PIC16LC620AT-04I/SS | IC MCU OTP 512X14 COMP 20SSOP |
| VI-243-IX-S | CONVERTER MOD DC/DC 24V 75W |
| VE-2TR-IX-S | CONVERTER MOD DC/DC 7.5V 75W |
| MAX5945EAX+T | IC NETWORK PWR CTRL 36-SSOP |
| ENC28J60T/ML | IC ETHERNET CTRLR W/SPI 28QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PIC16LC620T-04/SO | 功能描述:8位微控制器 -MCU .875KB 80 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC16LC620T-04/SS | 功能描述:8位微控制器 -MCU .875KB 80 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC16LC620T-04E/SO | 功能描述:8位微控制器 -MCU .875KB 80 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC16LC620T-04E/SS | 功能描述:8位微控制器 -MCU .875KB 80 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC16LC620T-04I/SO | 功能描述:8位微控制器 -MCU .875KB 80 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。