参数资料
型号: PIC16LF1527-I/MR
厂商: Microchip Technology
文件页数: 12/94页
文件大小: 0K
描述: MCU PIC 28KB FLASH 64QFN
产品培训模块: Configurable Logic Cell
8-bit PIC® Microcontroller Portfolio
标准包装: 40
系列: PIC® XLP™ 16F
核心处理器: PIC
芯体尺寸: 8-位
速度: 20MHz
连通性: I²C,LIN,SPI,UART/USART
外围设备: 欠压检测/复位,POR,PWM,WDT
输入/输出数: 54
程序存储器容量: 28KB(16K x 14)
程序存储器类型: 闪存
RAM 容量: 1.5K x 8
电压 - 电源 (Vcc/Vdd): 1.8 V ~ 3.6 V
数据转换器: A/D 30x10b
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 64-VFQFN 裸露焊盘
包装: 管件
181
7810C–AVR–10/12
Atmel ATmega328P [Preliminary]
19.7.5
Parity Checker
The Parity Checker is active when the high USART Parity mode (UPMn1) bit is set. Type of Par-
ity Check to be performed (odd or even) is selected by the UPMn0 bit. When enabled, the Parity
Checker calculates the parity of the data bits in incoming frames and compares the result with
the parity bit from the serial frame. The result of the check is stored in the receive buffer together
with the received data and stop bits. The Parity Error (UPEn) Flag can then be read by software
to check if the frame had a Parity Error.
The UPEn bit is set if the next character that can be read from the receive buffer had a Parity
Error when received and the Parity Checking was enabled at that point (UPMn1 = 1). This bit is
valid until the receive buffer (UDRn) is read.
19.7.6
Disabling the Receiver
In contrast to the Transmitter, disabling of the Receiver will be immediate. Data from ongoing
receptions will therefore be lost. When disabled (i.e., the RXENn is set to zero) the Receiver will
no longer override the normal function of the RxDn port pin. The Receiver buffer FIFO will be
flushed when the Receiver is disabled. Remaining data in the buffer will be lost
19.7.7
Flushing the Receive Buffer
The receiver buffer FIFO will be flushed when the Receiver is disabled, i.e., the buffer will be
emptied of its contents. Unread data will be lost. If the buffer has to be flushed during normal
operation, due to for instance an error condition, read the UDRn I/O location until the RXCn Flag
is cleared. The following code example shows how to flush the receive buffer.
Note:
For I/O Registers located in extended I/O map, “IN”, “OUT”, “SBIS”, “SBIC”, “CBI”, and “SBI”
instructions must be replaced with instructions that allow access to extended I/O. Typically
“LDS” and “STS” combined with “SBRS”, “SBRC”, “SBR”, and “CBR”.
Assembly Code Example
USART_Flush:
sbis
UCSRnA, RXCn
ret
in
r16, UDRn
rjmp
USART_Flush
C Code Example(1)
void
USART_Flush( void )
{
unsigned char
dummy;
while
( UCSRnA & (1<<RXCn) ) dummy = UDRn;
}
相关PDF资料
PDF描述
PIC16LF1783-E/SP IC MCU 8BIT 7KB FLASH 28-SPDIP
PIC16LF1823-I/ST IC MCU 8BIT FLASH 14TSSOP
PIC16LF1827-E/MV MCU 8BIT 4K FLASH 28UQFN
PIC16LF1828-E/P IC MCU 8BIT 7KB FLASH 20PDIP
PIC16LF1829-I/P MCU PIC 14KB FLASH 20-DIP
相关代理商/技术参数
参数描述
PIC16LF1527T-I/MR 功能描述:8位微控制器 -MCU 14KB Flash RAM 768b nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16LF1527T-I/PT 功能描述:8位微控制器 -MCU 14KB Flash RAM 768b nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16LF1613-I/SL 制造商:Microchip Technology Inc 功能描述:3.5KB FLASH, 256 RAM, 32MHZ INT. OSC, 10BIT ADC, ZCD, WWDT, - Rail/Tube 制造商:Microchip Technology Inc 功能描述:3.5KB Flash, 256 RAM, 32MHz Int. Osc, 10bit ADC, ZCD, WWDT, CRC, 14 SOIC .150in
PIC16LF1613-I/ST 制造商:Microchip Technology Inc 功能描述:3.5KB FLASH, 256 RAM, 32MHZ INT. OSC, 10BIT ADC, ZCD, WWDT, - Rail/Tube 制造商:Microchip Technology Inc 功能描述:3.5KB Flash, 256 RAM, 32MHz Int. Osc, 10bit ADC, ZCD, WWDT, CRC, 14 TSSOP 4.4mm
PIC16LF1703-I/SL 制造商:Microchip Technology Inc 功能描述:IC MCU 8BIT 2K FLASH 14SOIC