参数资料
型号: PIC16LF1827T-I/SO
厂商: Microchip Technology
文件页数: 56/109页
文件大小: 0K
描述: IC MCU 8BIT 4KB FLASH 18SOIC
标准包装: 1,100
系列: PIC® XLP™ mTouch™ 16F
核心处理器: PIC
芯体尺寸: 8-位
速度: 32MHz
连通性: I²C,SPI,UART/USART
外围设备: 欠压检测/复位,POR,PWM,WDT
输入/输出数: 16
程序存储器容量: 7KB(4K x 14)
程序存储器类型: 闪存
EEPROM 大小: 256 x 8
RAM 容量: 384 x 8
电压 - 电源 (Vcc/Vdd): 1.8 V ~ 3.6 V
数据转换器: A/D 12x10b
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 18-SOIC(0.295",7.50mm 宽)
包装: 带卷 (TR)
208
2570N–AVR–05/11
ATmega325/3250/645/6450
23.6.1
Analog Input Circuitry
The analog input circuitry for single ended channels is illustrated in Figure 23-8. An analog
source applied to ADCn is subjected to the pin capacitance and input leakage of that pin, regard-
less of whether that channel is selected as input for the ADC. When the channel is selected, the
source must drive the S/H capacitor through the series resistance (combined resistance in the
input path).
The ADC is optimized for analog signals with an output impedance of approximately 10 k
Ω or
less. If such a source is used, the sampling time will be negligible. If a source with higher imped-
ance is used, the sampling time will depend on how long time the source needs to charge the
S/H capacitor, with can vary widely. The user is recommended to only use low impedant sources
with slowly varying signals, since this minimizes the required charge transfer to the S/H
capacitor.
Signal components higher than the Nyquist frequency (f
ADC/2) should not be present for either
kind of channels, to avoid distortion from unpredictable signal convolution. The user is advised
to remove high frequency components with a low-pass filter before applying the signals as
inputs to the ADC.
Figure 23-8. Analog Input Circuitry
23.6.2
Analog Noise Canceling Techniques
Digital circuitry inside and outside the device generates EMI which might affect the accuracy of
analog measurements. If conversion accuracy is critical, the noise level can be reduced by
applying the following techniques:
1.
Keep analog signal paths as short as possible. Make sure analog tracks run over the
analog ground plane, and keep them well away from high-speed switching digital
tracks.
2.
The AVCC pin on the device should be connected to the digital V
CC supply voltage
via an LC network as shown in Figure 23-9.
3.
Use the ADC noise canceler function to reduce induced noise from the CPU.
4.
If any ADC port pins are used as digital outputs, it is essential that these do not
switch while a conversion is in progress.
ADCn
IIH
1..100 k
Ω
CS/H= 14 pF
VCC/2
IIL
相关PDF资料
PDF描述
PIC16F636T-I/ML IC PIC MCU FLASH 2KX14 16QFN
VI-B5F-IW-F1 CONVERTER MOD DC/DC 72V 100W
PIC16LF721-E/P MCU PIC 3.5KB FLASH 20PDIP
VI-B5D-IX-F3 CONVERTER MOD DC/DC 85V 75W
PIC16LF1825-E/ST MCU PIC 14KB FLASH 14TSSOP
相关代理商/技术参数
参数描述
PIC16LF1828-E/ML 功能描述:8位微控制器 -MCU 7 KB Flash 256B RAM 32 MHz Int Osc RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16LF1828-E/P 功能描述:8位微控制器 -MCU 7 KB Flash 256B RAM 32 MHz Int Osc RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16LF1828-E/SO 功能描述:8位微控制器 -MCU 7 KB Flash 256B RAM 32 MHz Int Osc RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16LF1828-E/SS 功能描述:8位微控制器 -MCU 7 KB Flash 256B RAM 32 MHz Int Osc RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16LF1828-I/ML 功能描述:8位微控制器 -MCU 7 KB Flash 256B RAM 32 MHz Int Osc RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT