收藏本站
参数资料
型号： PIC17LC766T-08/PT
厂商： Microchip Technology
文件页数： 94/159页
文件大小： 0K
描述： IC MCU OTP 16KX16 A/D PWM 80TQFP
标准包装： 1,200
系列： PIC® 17C
核心处理器： PIC
芯体尺寸： 8-位
速度： 8MHz
连通性： I²C，SPI，UART/USART
外围设备： 欠压检测/复位，POR，PWM，WDT
输入/输出数： 66
程序存储器容量： 32KB（16K x 16）
程序存储器类型： OTP
RAM 容量： 902 x 8
电压 - 电源 (Vcc/Vdd)： 3 V ~ 5.5 V
数据转换器： A/D 16x10b
振荡器型： 外部
工作温度： 0°C ~ 70°C
封装/外壳： 80-TQFP
包装： 带卷 (TR)
2000 Microchip Technology Inc.
DS30289B-page 39
PIC17C7XX
6.4
Interrupt Operation
Global Interrupt Disable bit, GLINTD (CPUSTA<4>),
enables all unmasked interrupts (if clear), or disables
all interrupts (if set). Individual interrupts can be dis-
abled through their corresponding enable bits in the
INTSTA register. Peripheral interrupts need either the
global peripheral enable PEIE bit disabled, or the spe-
cific peripheral enable bit disabled. Disabling the
peripherals via the global peripheral enable bit, dis-
ables all peripheral interrupts. GLINTD is set on
RESET (interrupts disabled).
The RETFIE instruction clears the GLINTD bit while
forcing the Program Counter (PC) to the value loaded
at the Top-of-Stack.
When an interrupt is responded to, the GLINTD bit is
automatically set to disable any further interrupt, the
return address is pushed onto the stack and the PC is
loaded with the interrupt vector. There are four interrupt
vectors which help reduce interrupt latency.
The peripheral interrupt vector has multiple interrupt
sources. Once in the peripheral Interrupt Service Rou-
tine, the source(s) of the interrupt can be determined by
polling the interrupt flag bits. The peripheral interrupt
flag bit(s) must be cleared in software before re-
enabling interrupts to avoid continuous interrupts.
The PIC17C7XX devices have four interrupt vectors.
These vectors and their hardware priority are shown in
Table 6-1. If two enabled interrupts occur “at the same
time”, the interrupt of the highest priority will be ser-
viced first. This means that the vector address of that
interrupt will be loaded into the program counter (PC).
TABLE 6-1:
INTERRUPT VECTORS/
PRIORITIES
6.5
RA0/INT Interrupt
The external interrupt on the RA0/INT pin is edge trig-
gered. Either the rising edge if the INTEDG bit
(T0STA<7>) is set, or the falling edge if the INTEDG bit
is clear. When a valid edge appears on the RA0/INT
pin, the INTF bit (INTSTA<4>) is set. This interrupt can
be
disabled
by
clearing
the
INTE
control
bit
(INTSTA<0>). The INT interrupt can wake the proces-
sor from SLEEP. See Section 17.4 for details on
SLEEP operation.
6.6
T0CKI Interrupt
The external interrupt on the RA1/T0CKI pin is edge
triggered. Either the rising edge if the T0SE bit
(T0STA<6>) is set, or the falling edge if the T0SE bit is
clear. When a valid edge appears on the RA1/T0CKI
pin, the T0CKIF bit (INTSTA<6>) is set. This interrupt
can be disabled by clearing the T0CKIE control bit
(INTSTA<2>). The T0CKI interrupt can wake up the
processor from SLEEP. See Section 17.4 for details on
SLEEP operation.
6.7
Peripheral Interrupt
The peripheral interrupt flag indicates that at least one
of the peripheral interrupts occurred (PEIF is set). The
PEIF bit is a read only bit and is a bit wise OR of all the
flag bits in the PIR registers AND’d with the correspond-
ing enable bits in the PIE registers. Some of the periph-
eral interrupts can wake the processor from SLEEP.
See Section 17.4 for details on SLEEP operation.
6.8
Context Saving During Interrupts
During an interrupt, only the returned PC value is saved
on the stack. Typically, users may wish to save key reg-
isters during an interrupt; e.g. WREG, ALUSTA and the
BSR registers. This requires implementation in software.
Example 6-2 shows the saving and restoring of infor-
mation for an Interrupt Service Routine. This is for a
simple interrupt scheme, where only one interrupt may
occur at a time (no interrupt nesting). The SFRs are
stored in the non-banked GPR area.
Example 6-2 shows the saving and restoring of infor-
mation for a more complex Interrupt Service Routine.
This is useful where nesting of interrupts is required. A
maximum of 6 levels can be done by this example. The
BSR is stored in the non-banked GPR area, while the
other registers would be stored in a particular bank.
Therefore, 6 saves may be done with this routine (since
there are 6 non-banked GPR registers). These routines
require a dedicated indirect addressing register, FSR0,
to be selected for this.
The PUSH and POP code segments could either be in
each Interrupt Service Routine, or could be subroutines
that were called. Depending on the application, other
registers may also need to be saved.
Address
Vector
Priority
0008h
External Interrupt on RA0/
INT pin (INTF)
1 (Highest)
0010h
TMR0 Overflow Interrupt
(T0IF)
2
0018h
External Interrupt on T0CKI
(T0CKIF)
3
0020h
Peripherals (PEIF)
4 (Lowest)
Note 1: Individual interrupt flag bits are set, regard-
less of the status of their corresponding
mask bit or the GLINTD bit.
2: Before disabling any of the INTSTA enable
bits, the GLINTD bit should be set
(disabled).
相关PDF资料
PDF描述
PIC17LC766T-08/L IC MCU OTP 16KX16 A/D PWM 84PLCC
PIC17LC766T-08I/PT IC MCU OTP 16KX16 A/D PWM 80TQFP
PIC17LC766T-08I/L IC MCU OTP 16KX16 A/D PWM 84PLCC
PIC17LC766-08/PT IC MCU OTP 16KX16 A/D PWM 80TQFP
PIC16LF1823-I/SL IC MCU 8BIT FLASH 14SOIC
相关代理商/技术参数
参数描述
PIC18C242/JW 功能描述:8位微控制器 -MCU 16KB 512 RAM 23I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18C242-E/SO 功能描述:8位微控制器 -MCU 16KB 512 RAM 23I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18C242-E/SP 功能描述:8位微控制器 -MCU 16KB 512 RAM 23I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18C242-I/SO 功能描述:8位微控制器 -MCU 16KB 512 RAM 23I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18C242-I/SO 制造商:Microchip Technology Inc 功能描述:8BIT CMOS MCU SMD 18C242 SOIC28
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*