参数资料
型号: PIC18F23K20-E/SO
厂商: Microchip Technology
文件页数: 17/42页
文件大小: 0K
描述: IC PIC MCU FLASH 4KX16 28-SOIC
标准包装: 27
系列: PIC® XLP™ 18F
核心处理器: PIC
芯体尺寸: 8-位
速度: 48MHz
连通性: I²C,SPI,UART/USART
外围设备: 欠压检测/复位,HLVD,POR,PWM,WDT
输入/输出数: 24
程序存储器容量: 8KB(4K x 16)
程序存储器类型: 闪存
EEPROM 大小: 256 x 8
RAM 容量: 512 x 8
电压 - 电源 (Vcc/Vdd): 1.8 V ~ 3.6 V
数据转换器: A/D 11x10b
振荡器型: 内部
工作温度: -40°C ~ 125°C
封装/外壳: 28-SOIC(0.295",7.50mm 宽)
包装: 管件
PIC18F2XK20/4XK20
DS41297F-page 24
Advance Information
2009 Microchip Technology Inc.
4.0
READING THE DEVICE
4.1
Read Code Memory, ID Locations
and Configuration Bits
Code memory is accessed one byte at a time via the
4-bit command, ‘1001’ (table read, post-increment).
The contents of memory pointed to by the Table Pointer
(TBLPTRU:TBLPTRH:TBLPTRL) are serially output on
PGD.
The 4-bit command is shifted in LSb first. The read is
executed during the next 8 clocks, then shifted out on
PGD during the last 8 clocks, LSb to MSb. A delay of
P6 must be introduced after the falling edge of the 8th
PGC of the operand to allow PGD to transition from an
input to an output. During this time, PGC must be held
low (see Figure 4-1). This operation also increments
the Table Pointer by one, pointing to the next byte in
code memory for the next read.
This technique will work to read any memory in the
000000h to 3FFFFFh address space, so it also applies
to the reading of the ID and Configuration registers.
TABLE 4-1:
READ CODE MEMORY SEQUENCE
FIGURE 4-1:
TABLE READ POST-INCREMENT INSTRUCTION TIMING DIAGRAM (1001)
Note:
When table read protection is enabled, the
first read access to a protected block
should be discarded and the read repeated
to retrieve valid data. Subsequent reads of
the same block can be performed normally.
4-bit
Command
Data Payload
Core Instruction
Step 1: Set Table Pointer
0000
0E <Addr[21:16]>
6E F8
0E <Addr[15:8]>
6E F7
0E <Addr[7:0]>
6E F6
MOVLW Addr[21:16]
MOVWF TBLPTRU
MOVLW <Addr[15:8]>
MOVWF TBLPTRH
MOVLW <Addr[7:0]>
MOVWF TBLPTRL
Step 2: Read memory and then shift out on PGD, LSb to MSb
1001
00 00
TBLRD *+
12
3
4
PGC
P5
PGD
PGD = Input
Shift Data Out
P6
PGD = Output
56
7
8
12
3
4
P5A
9
10
11
13
15
16
14
12
Fetch Next 4-bit Command
10
0
1
PGD = Input
LSb
MSb
12
34
56
12
3
4
nn
P14
Note
1:
Magnification of the high-impedance delay between PGC and PGD is shown in Figure 4-6.
(Note 1)
相关PDF资料
PDF描述
KSZ8842-PMQL IC SWITCH 10/100 32BIT 128-PQFP
PIC16F627AT-I/SO IC MCU FLASH 1KX14 EEPROM 18SOIC
V300A5C400BL2 CONVERTER MOD DC/DC 5V 400W
PIC16F627A-E/SS IC MCU FLASH 1KX14 EEPROM 20SSOP
KSZ8842-32MVL IC ETHERNET SW 2PORT BUS 128LQFP
相关代理商/技术参数
参数描述
PIC18F23K20-I/ML 功能描述:8位微控制器 -MCU 8 KB Enh Flash 768 RAM 25 I/O Pb Free RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F23K20-I/MV 功能描述:8位微控制器 -MCU 8KB Flash 768B RAM Enhanced Flash RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F23K20-I/SO 功能描述:8位微控制器 -MCU 8 KB Enh Flash 768 RAM 25 I/O Pb Free RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F23K20-I/SP 功能描述:8位微控制器 -MCU 8 KB Enh Flash 768 RAM 25 I/O Pb Free RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F23K20-I/SS 功能描述:8位微控制器 -MCU 8 KB Enh Flash 768 RAM 25 I/O Pb Free RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT