- 您现在的位置：买卖IC网 > PDF目录3810 > PIC18F2685-I/SP (Microchip Technology)IC PIC MCU FLASH 48KX16 28-DIP PDF资料下载
参数资料
| 型号： | PIC18F2685-I/SP |
| 厂商： | Microchip Technology |
| 文件页数： | 61/183页 |
| 文件大小： | 0K |
| 描述： | IC PIC MCU FLASH 48KX16 28-DIP |
| 产品培训模块： | Asynchronous Stimulus 8-bit PIC® Microcontroller Portfolio |
| 标准包装： | 15 |
| 系列： | PIC® 18F |
| 核心处理器： | PIC |
| 芯体尺寸： | 8-位 |
| 速度： | 40MHz |
| 连通性： | CAN，I²C，SPI，UART/USART |
| 外围设备： | 欠压检测/复位，HLVD，POR，PWM，WDT |
| 输入/输出数： | 25 |
| 程序存储器容量： | 96KB（48K x 16） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 1K x 8 |
| RAM 容量： | 3.25K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 4.2 V ~ 5.5 V |
| 数据转换器： | A/D 8x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 28-DIP（0.300"，7.62mm） |
| 包装： | 管件 |
| 产品目录页面： | 646 (CN2011-ZH PDF) |
| 配用： | DVA18XP280-ND - DEVICE ADAPTER 18F2220 PDIP 28LD |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页当前第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页
2011 Microchip Technology Inc.
DS39931D-page 153
PIC18F46J50 FAMILY
10.7.3.3
Mapping Limitations
The control schema of the PPS is extremely flexible.
Other than systematic blocks that prevent signal con-
tention caused by two physical pins being configured
as the same functional input, or two functional outputs
configured as the same pin, there are no hardware
enforced lock outs. The flexibility extends to the point of
allowing a single input to drive multiple peripherals or a
single functional output to drive multiple output pins.
10.7.4
CONTROLLING CONFIGURATION
CHANGES
Because peripheral remapping can be changed during
run time, some restrictions on peripheral remapping
are needed to prevent accidental configuration
changes. PIC18F devices include three features to
prevent alterations to the peripheral map:
Control register lock sequence
Continuous state monitoring
Configuration bit remapping lock
10.7.4.1
Control Register Lock
Under normal operation, writes to the RPINRx and
RPORx registers are not allowed. Attempted writes will
appear to execute normally, but the contents of the
registers will remain unchanged. To change these reg-
isters, they must be unlocked in hardware. The register
lock is controlled by the IOLOCK bit (PPSCON<0>).
Setting IOLOCK prevents writes to the control
registers; clearing IOLOCK allows writes.
To set or clear IOLOCK, a specific command sequence
must be executed:
1.
Write 55h to EECON2<7:0>.
2.
Write AAh to EECON2<7:0>.
3.
Clear (or set) IOLOCK as a single operation.
IOLOCK remains in one state until changed. This
allows all of the PPS registers to be configured with a
single unlock sequence, followed by an update to all
control registers, then locked with a second lock
sequence.
10.7.4.2
Continuous State Monitoring
In addition to being protected from direct writes, the
contents of the RPINRx and RPORx registers are
constantly monitored in hardware by shadow registers.
If an unexpected change in any of the registers occurs
(such as cell disturbances caused by ESD or other
external events), a Configuration Mismatch Reset will
be triggered.
10.7.4.3
Configuration Bit Pin Select Lock
As an additional level of safety, the device can be
configured to prevent more than one write session to
the RPINRx and RPORx registers. The IOL1WAY
(CONFIG3H<0>) Configuration bit blocks the IOLOCK
bit from being cleared after it has been set once. If
IOLOCK remains set, the register unlock procedure will
not execute and the PPS Control registers cannot be
written to. The only way to clear the bit and re-enable
peripheral remapping is to perform a device Reset.
In the default (unprogrammed) state, IOL1WAY is set,
restricting users to one write session. Programming
IOL1WAY allows users unlimited access (with the
proper use of the unlock sequence) to the PPS
registers.
10.7.5
CONSIDERATIONS FOR
PERIPHERAL PIN SELECTION
The ability to control Peripheral Pin Selection intro-
duces several considerations into application design
that could be overlooked. This is particularly true for
several common peripherals that are available only as
remappable peripherals.
The main consideration is that the PPS is not available
on default pins in the device’s default (Reset) state.
Since all RPINRx registers reset to ‘11111’ and all
RPORx registers reset to ‘00000’, all PPS inputs are
tied to RP31 and all PPS outputs are disconnected.
This situation requires the user to initialize the device
with the proper peripheral configuration before any
other application code is executed. Since the IOLOCK
bit resets in the unlocked state, it is not necessary to
execute the unlock sequence after the device has
come out of Reset.
For application safety, however, it is best to set
IOLOCK and lock the configuration after writing to the
control registers.
The unlock sequence is timing-critical. Therefore, it is
recommended that the unlock sequence be executed
as an assembly language routine with interrupts
temporarily disabled. If the bulk of the application is
written in ‘C’ or another high-level language, the unlock
sequence should be performed by writing in-line
assembly.
Note:
In tying PPS inputs to RP31, RP31 does
not have to exist on a device for the
registers to be reset to it.
相关PDF资料 |
PDF描述 |
|---|---|
| PIC18LF4682-I/PT | IC PIC MCU FLASH 40KX16 44TQFP |
| PIC32MX775F256L-80I/PF | IC MCU 32BIT 256K FLASH 100TQFP |
| PIC32MX575F512L-80I/PF | IC MCU 32BIT 512KB FLASH 100TQFP |
| PIC32MX695F512H-80I/MR | IC MCU 32BIT 512KB FLASH 64QFN |
| 6-100526-9 | Z-PACK F.CODING KEY |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PIC18F2685T-I/SO | 功能描述:8位微控制器 -MCU 96KB 3328bytes-RAM 25I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC18F26J11-I/ML | 功能描述:8位微控制器 -MCU 64KB Flash 4KBRAM 12MIPS nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC18F26J11-I/SO | 功能描述:8位微控制器 -MCU 64KB Flash 4KBRAM 12MIPS nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC18F26J11-I/SP | 功能描述:8位微控制器 -MCU 64KB Flash 4KBRAM 12MIPS nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC18F26J11-I/SS | 功能描述:8位微控制器 -MCU 64KB Flash 4KBRAM 12MIPS nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。